One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.
Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
You depend on your garage doors to provide safety and security at your home or office. They are also great for enhancing your property’s curb appeal and increasing its value. With their many moving parts and how they operate, you must have access to a reliable service company when something goes wrong. Houston residents and businesses trust us to make sure their garage doors will work when they need it to.

Garage Door Service Company


(The Wahl correction factor accounts for additional stress in the material due to shear forces, although these forces do not contribute to the spring's torque. These shear forces become significant in designs using a low spring index, which is to say, a relatively thick wire for the coil diameter. The correction factor is applied to scale up the stress S to better predict the fatigue lifetime of the spring.)

The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.

When a garage door goes off the track, the spring breaks, the door is dented or the garage door opener is on the fritz, a professional garage door repair specialist can help. The cost to have a garage door fixed varies, but the national average cost of garage door repair is $70-$110. The extent of the damage and the size and material of the door will affect the final cost. A garage door repair company generally charges a national average of $80 for a service call, which includes the first hour of labor and service, such as testing and inspecting the garage door and opener. Apart from labor, the garage door repair costs hinge on buying replacements parts. For example, a new spring costs an average of $60. Expect to pay several hundred dollars, though, if the door is beyond repair; a new garage door ranges in price from $200 to $4,000, and most homeowners spend an average of $800-$1,200.

The open-ended work-order trick: You may be very surprised if you allow work to proceed without signing a work order with a specified price. Or, you may sign a work order, and think you're protected against open-ended wallet-reaching, only to find a much higher price due at the finish than you expected, because you signed a "parts as needed" order that got loaded up with a long list of parts (that likely were still in serviceable condition). You might have been quoted a price, but then get a bill for that price plus a lot more added for the "service call" and the "parts", and be told the quote was just for the labor. While this is the normal way of abusing your finances down at the hospital, you shouldn't agree to it for a garage door service call. These guys are not doctors.


This opener is easy to install for most DIYers and comes with two remotes and a wireless keypad so you can open the door with a pin. If you are interested in having this smart-enabled you can purchase a separate kit to do so. The Safe-T Beam helps prevent accidents using a infrared beam that will open or close the door if a car is getting to close. 

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Our team of 100-plus technicians and service representatives takes care of you every step along the way. Our technicians are the best in the area. They’ll provide expert guidance as you consider your options, and then top-notch service to complete the repairs. When you want Cincinnati or Northern Kentucky garage door repair you can trust, choose AE Door & Window.
Had a quick response to my call. thought I might have to wait a couple of days to coordinate their schedule and mine. To my surprise I received service in one and one half hours. Not only that but there was no sales call, technician Mike was fully prepared to give me a quote and complete the work as his vehicle carried everything needed. He very efficiently completed the work and cleaned up after I selected from the options. He replaced the springs all rollers and made needed adjustments expeditiously. I would recommend this firm to anyone needing garage door repairs.read more
Here is what a winding cone looks like without the spring. The threads that grip the inside of the spring coils are ambidextrous, so you can use the same part on either right- or left-hand-wound springs. The cone size is specific for a certain inner diameter of springs, so if you have the wrong size, the cone will slip inside the spring (cone too small), or not fit (cone too big).
The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
In the market for overhead garage doors? Browse our selection of Pella garage doors. You'll find many options for single garage doors, double garage doors, insulated garage doors and even roll up garage doors. Lowe’s also carries garage door screens—great for those who love to spend hours in the garage, but don’t want to deal with the bugs and pests that invite themselves in. We also carry garage door hardware, garage door springs, garage door decorative hardware and garage door sensors, and don’t forget to ask about our garage door installation and garage door opener installation. Once you've decided a garage door fits your home, you'll need to find the garage door opener that works best for you. At Lowe’s, we carry Genie garage door openers, Chamberlain garage door openers and SOMMER garage door openers that will work seamlessly with your garage doors. We now offer a garage door opener that's compatible with your Iris home automation system, too. Whether you prefer opening your garage with a garage door remote or garage door keypad, you'll find it at Lowe’s. Our selection of garage remotes includes everything from universal garage door remotes to specific brands like Chamberlain garage door opener remotes and Chamberlain garage door keypads. We also carry backup batteries, nylon garage door rollers, garage door parts, garage door opener parts and rail extensions to make sure your garage door is in good working order. Plus, we even offer garage door installations services, which include garage door spring repair and replacements, and garage door cable repair and replacements. We can also replace your garage door weather seal, also known as garage door threshold seals, and install a new garage door opener battery.
Customers who have purchased this garage door opener for their homes have been mostly satisfied with the performance of it. Many have raved about how quiet it actually is—one said instead of hearing the metal squeak and clank like with their last one, only the sound of the “wooden door being jostled around as it is pulled up and down” is all you hear with this one. Customers were also happy with the features including the automatic closer when you forget to shut it after you go inside. Some had had issues with the manual being hard to understand while installing it themselves. But most were happy with the overall performance.

Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost, give us a call at 480-641-2301 or use our Contact Page.
Had a quick response to my call. thought I might have to wait a couple of days to coordinate their schedule and mine. To my surprise I received service in one and one half hours. Not only that but there was no sales call, technician Mike was fully prepared to give me a quote and complete the work as his vehicle carried everything needed. He very efficiently completed the work and cleaned up after I selected from the options. He replaced the springs all rollers and made needed adjustments expeditiously. I would recommend this firm to anyone needing garage door repairs.read more
While you may be able to increase efficiency by replacing the weather stripping at the bottom of an old garage door, the kind of insulation and energy efficient materials used in today’s new doors will make a drastic improvement on your garage’s energy efficiency. Just like the way a new garage door recoups its costs in increased home value, a new door will also quickly pay for itself in energy savings!
Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
If you live in a home where there are living quarters directly above the garage, Garage Guide DIY says force-sensing technology built into the B730 ensures a smooth operation, no matter what temperature it is in your garage. The unit adjusts the motor's power on the fly, keeping it running smoothly. Amazon reviewer Steven Bone says the B730/WD962KEV opener runs extremely quietly and is easy to install.
In order for you to find the right style door for your home, you need a tool that allows you to try out available options on a picture that approximates the look of your home. Using the Precision Door Designer, you'll easily create combinations of color, panel design and windows options that quickly educate you about the right style door for your home

Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 

At Garage Doors & More, we are an authorized dealer for Pella, Amarr, Clopay and Haas Garage Doors. Feel free to check out our site to find the door that fits best for your home. In the top navigation bar there is a drop down. The garage doors tab is where you will find traditional garage doors. There is also another tab that will lead you to a page for our energy efficient garage doors. Other tabs include pages for our Carriage Garage Doors and Wood Garage Doors. You can also click the button below to see some of our special offers!


GUESS YOU DON’T CARE to reply to my emails, so I'm posting it up here..... On Sep 8, 2018, at 2:52 PM, Joe Turiczek wrote: Thanks for the invoice, thanks for the service, thanks for the rapid response, thanks for Chris (the tech), but one note….. I’m a really handy guy, I repair and maintain nearly everything around the house, I am very mechanically adept, and I am also a highly skilled technical person that runs my own business by trade. I would have and could have repaired the belt myself, but I am traveling for business sooner than I could have ordered a belt, and did the repair….which means, I looked at the belts, I watched all the videos, it’s an EASY repair. I have belts down to a science, I’m really not an armchair DIY repair guy, I’m pretty good……That being said, I also shopped for prices of new belts for at least 30 mins or better, across easily 20-30 different parts and/or repair websites. Why am I telling you this? Because I think Chris, and your labor prices are spot on, and he deserved every cent, and your labor billing is more than fair…..however, I think your charge for the belt is a bunch of crap, it is nearly double of the HIGHEST price I found, which was $20-$25 higher than the average prices I found. Based on that alone, there is no way I could recommend, your otherwise FANTASTIC service, to anybody I know with a straight face. That’s just me being honest, because that’s who I am.
If you live in a home where there are living quarters directly above the garage, Garage Guide DIY says force-sensing technology built into the B730 ensures a smooth operation, no matter what temperature it is in your garage. The unit adjusts the motor's power on the fly, keeping it running smoothly. Amazon reviewer Steven Bone says the B730/WD962KEV opener runs extremely quietly and is easy to install.
If you're like most people shopping for a new garage door you want to accomplish 3 things: Get a really good idea how your new door will look on your home before you buy it. Show it to people you trust to get their opinion and get a price quote. You probably would also like to do all of this quickly and without any sales pressure. If that's true you're in the right spot. The Precision Door Designer will allow you to find the right style door, share a picture of it on Facebook and email your selected options for a free price quote. All in less than 10 Minutes! Select a collection to begin or continue reading to learn more.

An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. The large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes, but was still vulnerable to the replay attack.
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.

Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
J&S Overhead Garage Door Service also specializes in garage door opener repairs including broken gears, safety sensors, garage opener and chain adjustments and even remote and keypad replacements. Our technicians service major brands and carry necessary parts ad equipment parts on the trucks so you will never have to wait for a repair. If your opener can’t be repaired we do offer same day and same appointment professional installations offering several different garage door opener including chain and belt drive options.
Establish an alternate entry to your garage or update an existing one with our selection of garage entry doors. With an entry door, you will lose less heat or air when you enter your garage to work. Our variety of garage and outdoor organization materials will help you keep all the items in your garage neatly and efficiently organized while our floor coatings and utility flooring will help ensure your cement garage floors last longer than if they were left untreated.
×