Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.

We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.
When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Trading diameter for length: Observe that in the spring rate formula in the table above, factors D (diameter of coils) and N (number of coils) appear together in the denominator of the spring rate formula. Algebraically, given equal wire sizes, this means that the product of the coil diameter and overall length produces the spring torque, not the diameter or length alone. Physically, this means that you can trade off torsion spring coil diameter versus overall length in inverse proportions to maintain the same torque rate. Trade-off example: A spring with 2-inch diameter coils that is 36 inches long equals a 1.5-inch diameter spring that is 48 inches long, because the product in both cases is 72 (inches squared). This assumes that wire size is equal in the trade-off, and that you have not counted dead coils in the length. Service technicians use this principle to make quick substitutions for what's on their truck versus what you need. But if you understand this, you're ahead of many technicians who don't know this trick. Maybe now you can educate the next one you hire.
Finally, one of the most important garage door innovations over the years in increased child safety features. Sensors can detect when a child or pet is crossing the threshold while the door is closing, prompting it to stop immediately. Furthermore, doors can also sense when something is being pressed by the door, causing it to stop before inflicting a brutal crushing injury.

You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
Prices, like the garage doors themselves, run the gamut. You can pay as little as $400 for a door that you install yourself, or several thousand dollars for a high-end premium door that includes all the bells and whistles, including installation. A mid-range, 16-by-7-foot door will typically cost from $750 to $1,500, installed. Premium insulated steel doors run from $750 to $3,500. According to Remodeling Magazine’s 2017 Cost vs. Value report, the average national cost of a garage door replacement is $3,304.

When a garage door goes off the track, the spring breaks, the door is dented or the garage door opener is on the fritz, a professional garage door repair specialist can help. The cost to have a garage door fixed varies, but the national average cost of garage door repair is $70-$110. The extent of the damage and the size and material of the door will affect the final cost. A garage door repair company generally charges a national average of $80 for a service call, which includes the first hour of labor and service, such as testing and inspecting the garage door and opener. Apart from labor, the garage door repair costs hinge on buying replacements parts. For example, a new spring costs an average of $60. Expect to pay several hundred dollars, though, if the door is beyond repair; a new garage door ranges in price from $200 to $4,000, and most homeowners spend an average of $800-$1,200.
Luckily, your garage door is a pretty sound investment. According to Garage Wow Now, garage doors were ranked in the top three for home improvements whose costs are recouped through increased home value. Similarly, realtors regularly increased the list price of a home with a new garage door by 1 to 4 percent! That means, if you spend $2000 on a new garage door, you can increase the value of your home by almost $8000 if you have a $200,000 home. Furthermore, compared with the other two highest rated improvements — siding replacement and deck installation — a garage door replacement is far more affordable.
You depend on your garage doors to provide safety and security at your home or office. They are also great for enhancing your property’s curb appeal and increasing its value. With their many moving parts and how they operate, you must have access to a reliable service company when something goes wrong. Houston residents and businesses trust us to make sure their garage doors will work when they need it to.
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 
Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]
See the Sectional Overhead Garage Door catalog (PDF file) from the Prime-Line replacement hardware company. Their brochure Sectional Garage Door Torsion Spring Installation Instructions (PDF file, part number GD-12280) is brief but informative. Apparently you can only obtain their torsion springs as special order items through mom-and-pop type hardware stores like Ace and True Value, and not the big-box Home Depot and Lowes.
Are you in need of an overhead door? Do you have a door that jams or needs repair? Then, turn to the River Valley's most-trusted garage door professionals. Windsor Overhead Door, Inc. has a lineage that stretches back to 1974 and has served from its Russellville, Arkansas location for over 25 years. The company has recently passed to its third generation of owners who themselves have deep ties to the Windsor tradition of quality workmanship and customer service.
The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]
Customers who have purchased this garage door opener for their homes have been mostly satisfied with the performance of it. Many have raved about how quiet it actually is—one said instead of hearing the metal squeak and clank like with their last one, only the sound of the “wooden door being jostled around as it is pulled up and down” is all you hear with this one. Customers were also happy with the features including the automatic closer when you forget to shut it after you go inside. Some had had issues with the manual being hard to understand while installing it themselves. But most were happy with the overall performance.
Once the shaft, springs, and center bearing plate come down and lay on the floor, the old springs should be easy to get off and new ones slid on and assembled. Two bolts hold the center cones to the center bearing plate. The bearing on the center plate can be oiled while it is exposed from having the springs off. At this point it is a relief to be working with inert parts while standing on the floor rather than energized parts while up on the ladder. You might think it would save a little time to replace the spring with the shaft left up on the wall, but I found it was easier and safer to lower the works down to the garage floor first.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
Lift cable placement: On the standard residential door mechanism, the loops at the lower ends of the two lift cables loop over the two bottom roller shafts which project from the bottom bracket on the door. The upper cable ends fasten to the drums using one of the methods described above. The drums are positioned along the torsion shaft such that the inner edge of each drum is approximately over the edge of the door. The cable winds onto the drum from outside in, so at the top of travel the cable is winding onto the inner edge of the drum, vertical from the edge of the door where it is looped over the roller shaft. As the door is lowered, the cable winds out to the outer edge of the drum, and thus is a bit out from the vertical, but the cable still falls in the gap between the guide rails and door edge. My cables rub and slap on the rails a bit, but after 30 years and many 10,000s of cycles, they don't seem to have worn at all.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.

Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.


Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
Measurements: With the door in the down position, I measure a wire size of 0.273 inches, outside diameter of 2.0 inches, and overall length of 41.5 inches. Relaxing the spring shortens the length by about 7.5 coils of wire, so to estimate the relaxed length, we deduct the wire diamter of 0.273 inches times 7.5 from the 41.5 inch wound length, yielding an estimated relaxed length of 39.5 inches. The mean coil diameter is 2.0 - 0.273, or 1.73 inches. Perhaps this was actually a 40-inch-long spring with a 1.5 ID, 1.75 mean diameter, and 2.0 OD, but let's continue on calculating with the actually observed sizes. The number of coils in the relaxed spring is the relaxed length of 39.5 inches divided by the wire size of 0.273 inches, or about 145 coils. Deducting about 5 dead coils at the ends yields 140 active coils.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.

The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
Though we’ve grown a great deal, we still approach each customer with a focus on personalized service. We want to meet your needs as effectively as possible. We also provide a sense of urgency to each job, knowing that garage door needs often represent a significant life or work slowdown. Get in touch with us to schedule a visit, ask questions or to learn more about what we offer and how we can help get your garage door back up and running again.
Capable of lifting a seven-foot garage door up to 500 pounds in weight, the SilentMax 750 comes with a number of convenience features for automatic and remote use. The included wireless keypad and dual remote controls will ​insure that you are the only one that has access to the door. Compatible with a number of in-car remote systems like HomeLink, you can also keep the remotes at home if you are worried about losing the “keys.”​

For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
No matter what time or day of the week you require our services, we are always here to help. There are no additional fees to have us come by during the evening or weekend, so we’ll be able to offer you our premium service on a schedule that meets your needs. Contact Precision Garage Door Service of Lincoln today to book a free estimate and experience the high quality service that we have been providing to residents of Lincoln for many years.
We looked for wireless garage door openers that have the power to lift the heaviest doors and found that 1/2-horsepower motors are best suited for standard aluminum sectional doors used on most homes built from 1990 to today. The 3/4-horsepower garage door opener motors can lift wooden doors up to 550 pounds. Each model we looked at can open a standard 7-foot door, and extension kits are available if your door is taller.
An intermediate stage of the garage door opener market eliminated the DIP switches and used remotes preprogrammed to one out of roughly 3.5 billion unique codes. The receiver would maintain a security list of remotes to which it would respond; the user could easily add the unique remote's code to the list by pressing a button on the garage door opener while activating the remote control. The large number of codes made the brute force try-all-possible-digital-codes attacks infeasible, but the systems were still vulnerable to code grabbers. For user convenience, these systems were also backward compatible with the older DIP switch remote codes, but adding an old technology remote to the security list made the garage door opener vulnerable to a brute force attack to find the DIP switch code. The larger code space approach was an improvement over the fixed DIP switch codes, but was still vulnerable to the replay attack.
If the spring is broken near a winding cone, you might think you can remove and discard the short broken piece of spring from the cone, clean up the end of the long remaining spring, and insert that end into the cone. This is another extrememly risky improvisation. The shortened spring is not going to have the correct weight-bearing characteristics for the door, so you will not be able to balance the door properly. The shortened spring will be proportionately overwound, resulting in extra stress that will increase the expectation of another fracture. And the aging and history of the original spring being broken greatly increases the likelihood of another fracture at other locations.
Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Ankmar Denver is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
"I couldn't be happier, they solved a year long problem we had that a competing company of theirs (who installed the garage on our new home) couldn't fix! I feel Ric and Randy both (who have fixed a garage at my old house and my new house) take a lot of pride in their work, they are ethical and operate with integrity. I only want to work with Precision Garage Door from now on. I'd recommend them to anyone and everyone! ”
If the spring is broken near a winding cone, you might think you can remove and discard the short broken piece of spring from the cone, clean up the end of the long remaining spring, and insert that end into the cone. This is another extrememly risky improvisation. The shortened spring is not going to have the correct weight-bearing characteristics for the door, so you will not be able to balance the door properly. The shortened spring will be proportionately overwound, resulting in extra stress that will increase the expectation of another fracture. And the aging and history of the original spring being broken greatly increases the likelihood of another fracture at other locations.
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.

Garage Door Service Co

×