Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.
We specialize in garage door Spring Replacements. Broken Garage Door Springs (Extension and Torsion) can be repaired on the spot. J&S Overhead Garage Door Service will replace your broken garage springs today. We use only the highest quality garage door parts available. Our Extension Springs and Torsion springs are designed to last longer than standard residential springs.
The Genie Chain Drive garage door opener combines The Genie Chain Drive garage door opener combines powerful reliable performance with smooth operation to create a long-lasting and easy-to-install garage door opener. The unit's electronic push-button programming makes installation and setup fast and easy. Complete with accessories the system features a reliable DC motor that delivers quiet smooth operation ...  More + Product Details Close
Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.
There are many potential problems with garage doors, but the most common problem is the failure of one of the garage door springs. Torsion springs, which run along a bar above a closed door should never be replaced by a homeowner unless they have had specific training. To solve broken spring problems just give us a call. We are always available for free phone consultations and we love helping people fix their garage doors.
A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?
Screw - Screw-driven lift systems attach a long screw to the motor to move the garage door. These systems are powerful, fast, relatively quiet and require less maintenance than typical chain- or belt-driven systems. Genie and Overhead Door are two popular brands that make screw-driven systems. Based on our research of Genie’s line, you can expect to pay $244 on average for a screw-driven garage door opener.
Powerful, quiet and durable, Overhead Door® automatic garage door openers are designed for performance. And when you combine an Overhead Door® opener with one of our doors, you get an integrated system that maximizes performance and reliability. Our full line of automatic openers features a variety of power levels and specifications to handle different garage door weights and sizes. Each opener also comes with built-in, standard functions for the ultimate in safety, convenience and power. Don't know which opener to choose? Find the answers to some common questions to make sure you're buying the right garage door opener​. We offer a wide variety of additional garage door opener accessories.​​​

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
With all the styles offered by Clopay®, many homeowners fall in love with multiple doors. To help you choose the best garage door for your home, Clopay® has developed a comprehensive buying guide, outlining styles, construction materials, insulation, wind resistance, automatic garage door openers and more. We also allow you to view different door styles on your home with our Door Imagination System. Simply upload your home or choose from a variety of sample homes with one-car, two-car, and three-car garages to design the best garage door for your home.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
By watching the chalk mark while winding, you can count the number of turns applied, and confirm the number later. My standard-size door (7 foot height) with 4-inch drums has a nominal wind of 7-1/4 or 7-1/2 turns, which leaves 1/4 or 1/2 turn at the top-of-travel to keep the lift cables under tension. After 7 turns on the first spring, I clamped down the set-screws, weighed the door again, and found a lift of about 100 pounds in reduced weight. As expected, this wasn't quite half of the full 238 pounds, nor would it leave any torsion at the top-of-travel, so I added an 8th turn. The door now weighed 122 pounds on one spring, which was ideal. After winding the other spring, the door lifted easily, with only a few pounds apparent weight. This confirmed that the spring choice was properly matched to the door design. I engaged the electric opener trolley, and adjusted the opener forces down to a safer level suitable for the new, improved balance. The door was now ready for return to service.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.

Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
Overhead Door® openers​ and garage doors are built with longevity in-mind. By performing a few routine tasks, you can help ensure your garage door system stays safe and stands the test of time. One important part of garage door system routine maintenance is to make sure the photo-eyes have not gone out of alignment. The photo-eyes are the infrared sensors which monitor whether the space at the bottom of your garage door is clear. When these sensors are not lined up properly they will keep your door from closing. Make sure to occasionally check your photo-eyes’ alignment to ensure they are correctly detecting obstructions to keep your garage door safe and operating properly.
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
The Lifestyle garage door screen is a fully retractable garage screen door that works with your existing garage door. The Lifestyle features an industry first, fully retractable passage door for ease of entry and exit without having to retract the entire system. The Lifestyle garage screen is fully spring loaded, making opening and closing quick and easy.
Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
Since their invention in the 1920s, electric garage door openers have come a long way. Garage door openers work by using a trolley connected to an arm that attaches to the top of the garage door and slides back and forth on a track, which opens and closes the garage door. When operating the motor, a chain or belt turns and pulls the trolley along the track. A good garage door opener will have a horsepower of 1/2 HP, 3/4 HP, or 1-1/4 HP. Garage door openers have the ability to open and close a limited number of times in power outage emergencies. Security is something else to consider when purchasing an opener. It's helpful to have sensors that will stop the operation of the garage door when a person, vehicle, or other obstacle is in the way.
×