Good customer service is important for any product, but it is especially important for the class of garage door openers we considered. We looked primarily at models designed to be installed by a homeowner, not a professional. Even if you consider yourself to be pretty handy, you are sure to have questions at some point along the way. As such, we looked for companies that respond to all inquiries as well as for resources, such as a downloadable manual, to help with installation.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality.
Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from:

The prior clamping of the set-screws tends to have pressed a dimple into the hollow shaft and to have distorted the shaft's roundness into an eccentric shape. While releasing the set-screws, I was careful to loosen them enough to let the cone swing around any such distortions. I was also careful to observe any binding of the old cones on the eccentricity or burring on the shaft. The fit of the cone on the shaft is supposed to be loose enough to avoid binding, but if it were to occur one would have to be careful not to assume the spring was unwound when in fact the cone was just stuck on the shaft. If I had a stuck cone that I could not unwind with a little extra force, then I would have called in a technician to deal with it. In the worst case, I suppose the spring must be deliberately broken with some hazard, thus releasing it for a forceful disassembly, and the shaft and some other parts replaced. But this is an unlikely situation and in this case was not necessary.


Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.

GUESS YOU DON’T CARE to reply to my emails, so I'm posting it up here..... On Sep 8, 2018, at 2:52 PM, Joe Turiczek wrote: Thanks for the invoice, thanks for the service, thanks for the rapid response, thanks for Chris (the tech), but one note….. I’m a really handy guy, I repair and maintain nearly everything around the house, I am very mechanically adept, and I am also a highly skilled technical person that runs my own business by trade. I would have and could have repaired the belt myself, but I am traveling for business sooner than I could have ordered a belt, and did the repair….which means, I looked at the belts, I watched all the videos, it’s an EASY repair. I have belts down to a science, I’m really not an armchair DIY repair guy, I’m pretty good……That being said, I also shopped for prices of new belts for at least 30 mins or better, across easily 20-30 different parts and/or repair websites. Why am I telling you this? Because I think Chris, and your labor prices are spot on, and he deserved every cent, and your labor billing is more than fair…..however, I think your charge for the belt is a bunch of crap, it is nearly double of the HIGHEST price I found, which was $20-$25 higher than the average prices I found. Based on that alone, there is no way I could recommend, your otherwise FANTASTIC service, to anybody I know with a straight face. That’s just me being honest, because that’s who I am.
The winding technique is simply to (un)wind as far as one rod will go, where it is pressed against the top of the door, or nearly so, by the unwinding torsion. You insert the other rod in the next socket, remove the first rod, and continue. At any point you can stop and rest by leaving the active rod pressed against the door, where it will be held by the unwinding force. I would make a quarter-turn increment that way, and let go for a moment to collect my attention for the next increment, almost in a quiet, meditative alertness. While you can go from one quarter-turn and rod-swap to the next continually without letting go, working fast against the steady tension seemed to invite a kind of shakiness in my arms that was a bit unsettling. It isn't that there is much physical exertion, it is more that the tension is unrelenting, like peering over a precipice.
We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
It’s important to pick a door that suits the style of your house. If you live in a Craftsman bungalow, for example, you might want something that looks like the swing-out doors found on garages behind early Craftsman houses. Manufacturers of modern roll-up doors make them in styles that mimic the old swing doors, complete with faux strap hinges on the sides and a pair of handles flanking a deep groove in the center. 
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Of course, the best garage door openers offer much more than weather protection. They are quick and convenient when leaving or returning home. They can secure what might otherwise be a weak point of home security. Some can even alert you at work if your garage doors aren't closed properly. The challenge you face is finding the right one – this isn’t a product you can simply try out and return until you find the best fit for your situation.
Note the left winding cone with red spray paint. This shpritz of paint is applied to create fear and doubt in the mind of the do-it-yourselfer. Sometimes it is a color code for the wire size (using a DASMA standard, red indicating 0.2253 inch diameter wire). Sometimes it indicates the winding direction: red may indicate right-hand winding, but don't rely on that; do you own independent analysis. Sometimes it is a manufacturer's private code for another dimension than wire size. This color code is for the installer's information when the spring is new; I would not depend on interpreting the color code properly on an old spring, since one can't be certain of a correct interpretation without documentation from the original supplier.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
Since 1989, Henderson Garage Doors has specialized in the sale, installation, service and repair of residential and commercial door systems throughout the Baytown area. A family-owned and operated company, we’re committed to offering the finest products and delivering best in class service. We’re proud of our reputation for prompt, professional, and reliable service and we’d like to welcome you to the Henderson Family!
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
×