One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.
In 1992 the United States Consumer Product Safety Commission released new rules for automatic garage door openers. Anything manufactured after 1993 was required to include either an electric eye (a pair of sensors that detect an object obstructing the doorway) or a wall-mounted control button that users hold down in order to close the door entirely. Most manufacturers opted for the electric eye method, sometimes referred to as safety sensors.
If you are replacing an old garage door, the first step is to measure your garage opening to ensure you are choosing a door with the correct dimensions. Even if you feel confident that your door is a standard size, measuring first can help ensure that buying your door is an enjoyable and smooth process. View our installation guide to get the needed measurements for your door. If you find that you have an odd-sized garage door, use our QuickDraw tool to see how a specific model will look in your desired size. If you have a unique vision for your home's curb appeal, Clopay can also design custom garage doors to meet your specifications.
Garage remotes work by sending a coded signal via radio frequency to the garage door opener. If this code matches that of the opener, then the motor will operate and raise or lower the door. Older devices use a single coded switch, whereas newer systems utilise a rolling code that changes each time the remote is used, increasing the security of the door by offering billions of combinations.
Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.
Permits must be applied for when you are building a new home or structure. This permit will cover the building of the structure and cover the inspection for your garage door. The inspection process for a new door is pretty simple. The county will want to make sure that you have a garage door installed that meets local wind rating standards. In Mecklenburg County, that standard is 90 mph. That means that your door must be rigid enough to withstand 3 second gust by winds of up to 90 miles per hour.
As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.
The various increments of standard wire sizes differ by only about 0.010 inch, so calipers or a micrometer would be the tool to use to be certain of the stepped size you have, or else a trustworthy ruler marked in tenths of an inch to use the measure-10-turns-and-divide-by-10 trick. The most common wire sizes in the US are 0.207", 0.218", 0.225", 0.234", 0.243", 0.250", and 0.262".
When a garage door goes off the track, the spring breaks, the door is dented or the garage door opener is on the fritz, a professional garage door repair specialist can help. The cost to have a garage door fixed varies, but the national average cost of garage door repair is $70-$110. The extent of the damage and the size and material of the door will affect the final cost. A garage door repair company generally charges a national average of $80 for a service call, which includes the first hour of labor and service, such as testing and inspecting the garage door and opener. Apart from labor, the garage door repair costs hinge on buying replacements parts. For example, a new spring costs an average of $60. Expect to pay several hundred dollars, though, if the door is beyond repair; a new garage door ranges in price from $200 to $4,000, and most homeowners spend an average of $800-$1,200.
In my case, removing and replacing the relaxed springs required that I take down the assembly: torsion shaft, lift drums, and bearings. Doing that requires unbolting the center bearing plate from the wall, removing the drums from the shaft, and finally sliding the shaft back and forth out of the end bearings to remove the whole assembly off the wall. I am fortunate to have a lot of clearance in this garage to make the disassembly simpler. Tighter clearance to walls or ceiling would make disassembly a more difficult manipulation.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.
And for some extra features, you'll appreciate accessing the system through the MyQ smartphone app. You can set up this Chamberlain opener to automatically close the door after 1, 5, or 10 minutes, which is great for people who are a bit forgetful. We also really like the motion-detecting control panel, which turns on lights whenever it records nearby movement.
While you may be able to increase efficiency by replacing the weather stripping at the bottom of an old garage door, the kind of insulation and energy efficient materials used in today’s new doors will make a drastic improvement on your garage’s energy efficiency. Just like the way a new garage door recoups its costs in increased home value, a new door will also quickly pay for itself in energy savings!
I make no recommendations of, and have no connection to, any of the following suppliers. These are just those whom I have learned about from my Web searches, from correspondence with those sending email about their experiences, or directly from the suppliers. I have removed several contacts that were generating complaints to me from dissatisfied customers. I have added this list to this page due to all the email queries I was receiving daily asking where to obtain parts. If you are a supplier and would like to be added to the list, see my email address at the end of this page.
When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
We have everything needed and the expertise required to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, one of our team members will be happy to help you diagnose the problem and then apply an effective solution. Our repair services include repairs for springs, cables, rollers, tracks, sections, and more! Is your door noisy? We know the right way to fix it! Call us any timeyou need us to fix a problem.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.