Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
The wire size and winding direction are easily discovered and proved, as I will explain below. You absolutely must know and understand the critical measurements of your old springs to order replacements. This assumes that the old springs were the correct to begin with; it is not uncommon to have incorrectly sized springs on a door due to a previous sloppy installation, or a significant change in weight of the door.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.


We are a family owned and operated company with local offices in various cities. We have offices in Arizona — from Phoenix to Tucson; Nevada— covering the entire Las Vegas metropolitan area, from North Las Vegas to Henderson; the Sunflower State of Kansas, from Wichita to Junction City; Wisconsin — spanning the entire Milwaukee county, from Fox Point to South Milwaukee; and Michigan, with our base in Sterling Heights.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.

The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
Bringing simple convenience to your home the Chamberlain Bringing simple convenience to your home the Chamberlain 1-1/4 HP Garage Door Opener provides instant garage access at your fingertips. Featuring innovative built-in smartphone control and battery backup this system ensures that you're never locked out of your home. Boasting a steel reinforced belt drive the B970 features anti-vibration technology ...  More + Product Details Close
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
Clopay, a garage door manufacturer, provides online installation manuals for their products. These include excellent mechanical diagrams and brief instructions for winding torsion springs on their doors. Of course, this is specific to their product designs, which may or may not match what you have. Note that some of their products involve the "EZ-Set assembly option" mechanisms that use a geared housing for winding (instead of standard winding cones) and non-standard geometry for the drums. Clopay should get an award for at least acknowledging in their instructions that you might be able to install your own new door (although they insist you must not take out an old one if it has torsion springs).
Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
Overhead Door® openers​ and garage doors are built with longevity in-mind. By performing a few routine tasks, you can help ensure your garage door system stays safe and stands the test of time. One important part of garage door system routine maintenance is to make sure the photo-eyes have not gone out of alignment. The photo-eyes are the infrared sensors which monitor whether the space at the bottom of your garage door is clear. When these sensors are not lined up properly they will keep your door from closing. Make sure to occasionally check your photo-eyes’ alignment to ensure they are correctly detecting obstructions to keep your garage door safe and operating properly.
Clopay, a garage door manufacturer, provides online installation manuals for their products. These include excellent mechanical diagrams and brief instructions for winding torsion springs on their doors. Of course, this is specific to their product designs, which may or may not match what you have. Note that some of their products involve the "EZ-Set assembly option" mechanisms that use a geared housing for winding (instead of standard winding cones) and non-standard geometry for the drums. Clopay should get an award for at least acknowledging in their instructions that you might be able to install your own new door (although they insist you must not take out an old one if it has torsion springs).
The Chamberlain Whisper Drive takes control to a higher level than other models with its door and light automation features. The internal control panel has a sensor for motion-activated lighting. In addition, door closing can be instant or set automatically for 1, 5 or 10 minutes. We give this feature a top-notch rating because, should you forget to close your door, your garage will secure itself.
Not interested in paying for maintenance on an outdated and failing system? Our installation services mean that you can have a brand new, high quality garage door installed in place of your existing model. Because we carry such a diverse range of products from the most industry-respected manufacturers, we’re sure to have a model that fits your needs and budget.
Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.
Cost was $88 for 2 pairs of springs, plus $21 shipping. (I had to order 2 pairs to meet the $50 minimum order.) They came with new cones inserted as shown at that price, so I didn't bother trying to remove and reuse the old cones to save a few dollars. The cones are quite difficult to remove from old springs and to insert in new ones, and the spring supplier will have the right tooling to do that easily. That was the best price I could find on the Web at the time, and didn't seem out of line with what parts like this might cost at at the building supply (if they only sold them). Contractors buy these much cheaper in quantities; they're just an ordinary high-carbon steel wire turned on a winding machine. I also found Web sites asking a lot more money, obviously trying to cash in on search-engine traffic from do-it-yourselfers. Others report that some local dealers sell springs at retail, but at a high price that eliminates any economy versus having them installed.

Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.


Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Once the springs are torqued, the setscrews tightened, and the locking pliers and winding rods removed, do not play with turning the torsion bar using the winding rods. Doing so even momentarily can relieve the tension on the lift cables, which then easily slip off the drums. Replacing the cables on the drums can be difficult without repeating the entire spring unwinding-winding procedure again, and the cables can be damaged if tension is applied while they are off the drums.
The Decko 24300’s 3/4-HP motor provides the power you need if you've got a big or heavy door and, while it may not have all the bells and whistles of some “deluxe” models, the Decko does everything you need it to do. We appreciate the fact that this model comes with two remotes, an internal panel for controlling the lighting and opening/closing the door, a wireless external keypad with a security code, and a rolling code access system that keeps intruders out of your garage. The Decko will save you a few dollars over some of the more premium garage door openers, but it will still give you an excellent performance.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel.[1] The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers.[1] The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs.[2] A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.[3]
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
Smart garage door openers aren't as expensive or hard to find as you might think. In fact, no matter what smart home platform you're using, there is an opener that will work for you. Smart garage door controllers add convenience like remote access, voice control, scheduling and vehicle detection to your garage door. You'll never need to wonder if you left it open ever again. 
Garage doors cause injury and property damage (including expensive damage to the door itself) in several different ways. The most common causes of injury from garage door systems include falling doors, pinch points, improperly adjusted opener force settings and safety eyes, attempts at do-it-yourself repair without the proper knowledge or tools, and uncontrolled release of spring tension (on extension spring systems).
Carter door: Garage doors in Florida come with extra bracing on the back and are wind-loaded to protect against hurricanes. The average with is 350 lbs. but some can weigh as much as 800 lbs. It can cost up to $1,000 dollars to replace a steel two-car garage door and if it's made of wood it can cost you up to $5,000 dollars. Some customized doors can be as much as 20 - 30k.

The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.
The torsion shaft with lift drums on the ends is above the door. The standard residential door shaft is a 1-inch outside diameter hollow steel tube. The inside diameters of the bearings, drums, and winding cones are sized to loosely fit that 1-inch diameter shaft. At the center is a bearing plate, on either side of which are the torsion springs, or in some cases just one larger spring. The spring pictured on the left in the photo is broken about 1/4 of the way in from its left end. The black shaft with dangling rope and door bracket is the track for the electric opener.
Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.
Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
Don’t miss out on all the modern conveniences and safety improvements that homeowners with automatic garage door openers enjoy. You deserve a garage door that you can open and close remotely. You deserve a garage door that doesn’t force you to get out into the rain and snow to operate it. You can have it with a simple phone call to A1 Garage Door Repair Madison. You can even choose form our fine selection of garage door opener products and have us install it for you.
Whether you are a new homeowner looking to personalize your home or you need to replace your existing garage door, Clopay® makes it easy to find the right choice for your home. Your garage door can account for up to 30% of your home’s façade, so choosing the right style can have a great impact on your curb appeal. Clopay doors are available in a variety of styles including carriage-house, raised-panel and modern, all with convenient overhead operation. Choose from a variety of colors, woodgrain finishes, materials and hardware to complement your home’s exterior.
×