A knowledgeable installer with good inventory can offer you upgraded spring lifetimes by using longer, heavier springs than were originally installed. For example, you may be offered more expensive springs with expected lifetimes of 15, 25, or even 100 thousand cycles, instead of the standard 10 thousand. The difference in labor to substitute this upgrade is nil. Since the dealer's cost of springs is proportional to weight, and typically a small part of the job price anyway, the dealer's cost for this upgrade is slight. This would seem to be a excellent option to offer every customer, and if correctly calculated and reasonably priced, one that you should take as cost-effective. Yet you may not be offered such an upgrade, if the installer is not adept at making the rather simple calculations, or if the optional springs are not on his truck, or if you're not around to be asked, or if the installer just doesn't like selling or taking time to discuss such details.

With garage door installation costs, these numbers also include the actual purchase of the new door and other hardware, including the tracks, adhesives, connectors and fasteners. Keep in mind that if these numbers seem extreme, garage door replacement and upgrades can yield, on average, one of the highest returns on investments for homeowners — with an expected 85 percent.


Torsion springs are devices that lift most of the weight of a garage door so that the door can be opened manually or by an electric opener. The torsion principle is applied via an efficient and economical apparatus consisting of a torsion shaft under spring torsion, which turns lift drums, which wind cables attached to the door near the bottom. All of this apparatus is mounted over the top of the door. The energy stored is sufficient, in an uncontrolled release, to break things, hurt you, or perhaps even kill you. The same could be said of jacking up your car to change a tire, or mowing your lawn, or raising children, so it is not crazy to want to do this yourself.

I make no recommendations of, and have no connection to, any of the following suppliers. These are just those whom I have learned about from my Web searches, from correspondence with those sending email about their experiences, or directly from the suppliers. I have removed several contacts that were generating complaints to me from dissatisfied customers. I have added this list to this page due to all the email queries I was receiving daily asking where to obtain parts. If you are a supplier and would like to be added to the list, see my email address at the end of this page.
GREAT Company. Called in at 1:30 on a Saturday and my issue was fixed by 3:30 that same day. Our service tech Ken was a great guy who was A++++Can't ask for a better experience than I had with this company. I highly recommend this company and Ken to everyone. And their rates are very fair. GREAT Company to deal with. I wish any other contractor I've dealt with were even half as good as this company. A+++++++ all the way.read more
While winding or unwinding, one must be mindful of the possibility that the spring could break during winding process itself. If that should happen while the spring is significantly torqued, hazardous forces on the winding bar will suddenly become unbalanced, and the bar will take an unexpected jump, possibly injuring your hand or anything else in its path. At the same time, the spring remnants, although captured on the torsion bar, will create a frightening racket that would give the bravest soul a start. So your winding technique should be firmly in control of the rods, and you should not be so delicately perched on a ladder such that a startle will result in a fall.
Door repair business advice (warning to consumers, you are not allowed to know this): Thinner wire is excellent for shortening spring lifetimes, lightening your inventory on a service truck, and getting paid for frequent service calls. This is why your industry chooses to set "standard" springs to have thin wire and despicably short lifetimes. If you want to maximize profits and fleece your customers, install springs that predictably break in about 7 years on a door that should last decades, even though it is just as easy for you to install slightly more expensive springs that should last the life of the door. Remember that the customer wanted the cheapest price, so you need not feel any guilt about this low-balling.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
Manufacturers and distributors of torsion springs believe they are better off not retailing their product directly to the public. They believe they are maintaining higher prices for their product by restricting sales "to the trade." One brochure for parts even flatly stated, "We do not sell to the end user. We protect our dealers," which would seem to be prima facie evidence of an illegal restraint-of-trade scheme. But this is an old story which is true of virtually every product and service, going back to medieval guilds and before.
The first garage door opener remote controls were simple and consisted of a simple transmitter (the remote) and receiver which controlled the opener mechanism. The transmitter would transmit on a designated frequency; the receiver would listen for the radio signal, then open or close the garage, depending on the door position. The basic concept of this can be traced back to World War II. This type of system was used to detonate remote bombs. While novel at the time, the technology ran its course when garage door openers became popular. While the garage door remote control transmitter is low power and has limited range, its signal can be received by other, nearby, garage door openers. When two neighbors had garage door openers, then opening one garage door might open the neighbor’s garage door as well.
Finally, one of the most important garage door innovations over the years in increased child safety features. Sensors can detect when a child or pet is crossing the threshold while the door is closing, prompting it to stop immediately. Furthermore, doors can also sense when something is being pressed by the door, causing it to stop before inflicting a brutal crushing injury.
Trading wire size for length, diameter, or cycle life: Now we are really going to save you some money, if you just recall your high school algebra class (and I don't mean that cute cheerleader who sat next to you). If you further understand the role of the 4th power of the spring wire size (letter d in the formulas above) in the numerator of the spring rate formula, and how to increase or decrease d to compensate for changes in length, diameter, and cycle life, then you're qualified for elite spring calculations. Matching springs is a matter of equating the 4th power of the proportion in wire size change to the proportion of change in the diameter or length or the product of both diameter and length. However, it is usually best to only increase wire size when substituting a spring, since this does not derate the cycle life. If you observe that the formula for bending stress is proportionate to the inverse 3rd power of the diameter, then physically a proportionate increase in wire size will result in a dramatic increase in cycle life of the 3rd power of that proportion. Trade-off example: Yawn with me while we ponder my original spring once more. Let's say I was in a fit of engineering mania, and wanted to replace my spring having a 0.2253 inch diameter wire (d = 0.2253) with a 0.262 wire version (d = 0.262). How much longer is the spring with equal torque rate, assuming we use the same coil diameter? The proportion of this change is 0.262/0.2253 = 1.163, and the 4th power of that is 1.83. This means the length must increase by a factor of 1.83 (again, not counting dead coils). Recalling that the length in Example 1 was 102 non-dead coils, the heavier wire spring must be about 1.83*102 = 187 coils, which when adding 5 dead coils and multiplying by the wire size to get the overall length, is (187+5)*0.262 = 50 inches, versus 24 inches in the original. So using this heavier wire more than doubles the length (and thus the mass and thus the cost). While the cost about doubles, the stress goes down by the inverse 3rd power of the wire size proportion, or 1/(1.163**3) = 0.64. Sress is favorably, non-linearly related to cycle lifetime (halving the stress more than doubles the lifetime), so this decreased stress should more than double the expected lifetime of the spring. While the up-front cost is more, the true cost of an amortized lifetime is much less. In short, per cycle it is cheaper. Ah, the wonders of engineering calculations! Conclusion: Observe that the stress formula (and thus the cycle lifetime) depends only on wire diameter (d) for equal torques. Thus the only way to improve cycle lifetime is to use heavier wire. For equal torques, heavier wire size, due to the exponents in the formulas, increases cycle lifetime much faster than it increases mass (and thus cost), physically speaking.
Steel entry doors - when a garage is being fitted with new doors, it is also a good idea to consider a separate single 3x68 exterior door with half-glass and locksets too. These may require some carpentry, but they are a good way to allow for some flexibility in the choice of larger garage door, and can ensure that the homeowner will have more than a single way in or out of the structure. The average costs for such a feature range from $250 to $1000 each.
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
Since their invention in the 1920s, electric garage door openers have come a long way. Garage door openers work by using a trolley connected to an arm that attaches to the top of the garage door and slides back and forth on a track, which opens and closes the garage door. When operating the motor, a chain or belt turns and pulls the trolley along the track. A good garage door opener will have a horsepower of 1/2 HP, 3/4 HP, or 1-1/4 HP. Garage door openers have the ability to open and close a limited number of times in power outage emergencies. Security is something else to consider when purchasing an opener. It's helpful to have sensors that will stop the operation of the garage door when a person, vehicle, or other obstacle is in the way.
Scott did an amazing job. Your customer service team is excellent. I emailed late on Thanksgiving night my request for service. Your team called my house within 30 minutes and set up an appointment for the following morning. Scott came out and was great. I had purchased the lifetime warranty package with Precision before, and your team delivered. I highly recommend anyone getting a repair to purchase the lifetime warranty package since your team stands behind your product. Rarely do I write reviews - but am happy to share great information on great companies. Thanks for the great service!

All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
To estimate the maximum physical force required to wind these springs, consider that they are balancing the weight of the door with a torque applied to a lift drum on each end of the torsion shaft. The lift drums have a 2-inch radius, which is the standard residential size, and corresponds conveniently to about a 1-foot circumference. If we pessimistically assume the 10-by-7-foot door has a weight of 350 pounds, this implies a torque of 350 pounds on a 2-inch radius, that is, 700 inch-pounds, or 58 foot-pounds. Each of the two springs should be exerting slightly less than half of the balancing torque, or 29 foot-pounds. Compare this to, say, the bolts in an automobile, which are typically torqued to values of about 50 foot-pounds, or tire lug nuts, which may be torqued to well over 100 foot-pounds.
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
Hello Scott and thank you for the very nice 5 star review. John, our Tech, will be very happy too. I will review our on-phone quoting system after listening to your call and see if we can get better at more accurate pricing. It is just so tough to know exactly what is going on at the site and the extent of the repair until we set eyes on it. We will try to get better at it...I promise. Thanks again.

Manufacturers and distributors of torsion springs believe they are better off not retailing their product directly to the public. They believe they are maintaining higher prices for their product by restricting sales "to the trade." One brochure for parts even flatly stated, "We do not sell to the end user. We protect our dealers," which would seem to be prima facie evidence of an illegal restraint-of-trade scheme. But this is an old story which is true of virtually every product and service, going back to medieval guilds and before.


Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
The typical electric garage door opener consists of a power unit that contains the electric motor. The power unit attaches to a track. A trolley connected to an arm that attaches to the top of the garage door slides back and forth on the track, thus opening and closing the garage door. The trolley is pulled along the track by a chain, belt, or screw that turns when the motor is operated. A quick-release mechanism is attached to the trolley to allow the garage door to be disconnected from the opener for manual operation during a power failure or in case of emergency. Limit switches on the power unit control the distance the garage door opens and closes once the motor receives a signal from the remote control or wall push button to operate the door.[3]
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly.
Whether you're looking for the beautiful " Carriage House" style that adds beauty to your home, an energy efficient door that keeps your home warm or cool while reducing energy bills, or just needs a Custom Garage Door we've got a model that fits your needs. Learn more here.. Or come visit us at our new showroom to check out 25+ door models in person.
I mentioned earlier that this apparatus had at least one prior spring replacement, with a single longer spring having been replaced by two shorter springs. The clamping of the original spring had pressed dimples and an eccentric distortion into the hollow shaft. While this distortion was large enough to block the old cones from sliding across, I was able to remove the old hardware by just sliding them in the other direction. I did not have to bother trying to press out this distortion, since I could just work around it.

Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
Powerful, quiet and durable, Overhead Door® automatic garage door openers are designed for performance. And when you combine an Overhead Door® opener with one of our doors, you get an integrated system that maximizes performance and reliability. Our full line of automatic openers features a variety of power levels and specifications to handle different garage door weights and sizes. Each opener also comes with built-in, standard functions for the ultimate in safety, convenience and power. Don't know which opener to choose? Find the answers to some common questions to make sure you're buying the right garage door opener​. We offer a wide variety of additional garage door opener accessories.​​​
The salesman-disguised-as-technician trick: In this trick, you arrange for a service call to your home, perhaps paying a small fee up-front, and a neatly uniformed man arrives in a very technical-looking truck, carrying an impressive tool kit. He carefully examines your door, perhaps using some impressive testing devices to lend weight to his expertise. He then condemns your door as not worth repairing, and tells you, to his sincere regret, that you must have a new one. In fact, this technician is not a technician, but a salesman who only sells, and does not repair, doors. Even if he doesn't sell you, he is doing well just collecting fees for service calls that are no more than sales visits. He doesn't actually have to ever fix anything, and he may not even be capable of doing so himself. He's an expert at selling, which genuine technicians are not. In the worst case, when you refuse to buy a whole new door, he might refuse to follow up with a visit from an actual technician, either outright, or only with an unacceptable delay ("we're too busy to get a guy out until next week", when your car is trapped). If you find yourself closing in on this situation, then politely invite him to leave, and try someone else. That is your right, and in fact the only power you have to bargain in such circumstances. At that point, he may offer to promptly bring in his competent colleague, who will turn up lacking charm and looking awful, but might actually do the work, possibly at a fair price. If so, you will have beaten a legal variation of the classic illegal bait-and-switch (see below). The switch was attempted, but not required, which makes this legal. This is a hazard of any direct-sales situation. Because it rarely appears in everyday retail sales, it can surprise the unwary.
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.

Most styles, whether traditional or contemporary, feature panels, trim, and other detailing. Doors with true frame-and-panel construction tend to be sturdier than those with decorative detail that is merely glued or nailed on. Many styles have glass panels on the top row, which looks inviting from the street and brings daylight inside. You can also find roll-up doors with shatterproof glass or frosted plastic in all the panels, for a more modern look.


When your garage door starts acting up, more often than not it is telling you it's time to do a bit of maintenance. So, before hitting the panic button, try these simple repairs. First, examine the rollers and tracks. If you can't remember the last time you cleaned them (and they look the part!), give them a good brushing and then add some lubricant. Next, perform these simple garage door maintenance tasks.
As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!

Wood doors range from midprice to very expensive, depending on whether they consist of a lightweight wooden frame filled with foam insulation and wrapped in a plywood or hardboard skin (the least expensive) or are true frame-and-panel doors made of durable mahogany, redwood, or cedar. Wood doors usually carry a short warranty, perhaps only one year. 
An enantiomorphic (mirrored) pair of springs, such as my standard door uses, will consist of one left-hand and one right-hand spring. Note that this "right" and "left" has nothing necessarily to do with whether the spring is mounted on the left or right of the center bearing plate. Indeed, with my standard door, if you stand inside the garage, facing out, then the spring to the left is a right-hand-wound spring, and the spring to the right is a left-hand-wound spring. The photos above and below of the broken spring show that it is a right-hand-wound spring.
Checking if the lift drums need resetting: The old position of the lift drums on the shaft may have slipped or otherwise lost the the proper position, requiring a reset of the drum position on the torsion shaft. You will also reset the drums if you are replacing the lift cables, since the new cables will not exactly match the length of the old ones. Problems like uneven tension on the cables, or a tilted door, or a door that doesn't easily stay aligned with the tracks, can be due to an improper "set" of the drums on the shaft. So one shouldn't assume the old positions are correct. Setting the drums on a "fresh" part of the shaft will avoid the possibility of damaging the shaft from retightening in the same dimples.
If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and
As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.

It you have a tilt-up door, you are looking at a $150 - $200 repair or replacement. If it's a roll-up door it's going to cost you more. Roll-up door spring repair or replacement is usually around $200 - $250 for a 2 car door. If the brackets need to be disassembled to remove the springs due to the shaft not sliding sideways enough it will cost you an additional $50 - $100.
We want to serve you not only today, but also in the years ahead. To do that, we make sure that we provide prompt, professional, well-trained technicians that efficiently get the job done right the first time. We take pride in doing everything possible to eliminate warranty issues and to ensure that our clients are thoroughly pleased and return to us for all garage door needs.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Cycle lifetime unchanged by diameter-versus-length tradeoffs: Since the material stress (and thus cycle lifetime) for equal torques varies only with d, and not D or N, trading coil diameter (D) for spring length (N) in this fashion has no effect on cycle lifetime. Long and skinny, versus shorter and fatter, they'll wear the same if they have the same wire size and diameter-length product. The game of life is all about wire size when it comes to springs (see below).
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
×