Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
In 1992 the United States Consumer Product Safety Commission released new rules for automatic garage door openers. Anything manufactured after 1993 was required to include either an electric eye (a pair of sensors that detect an object obstructing the doorway) or a wall-mounted control button that users hold down in order to close the door entirely. Most manufacturers opted for the electric eye method, sometimes referred to as safety sensors.
The technician that came out, Todd Noel, was very friendly and professional. He fixed my problem quickly and did not overcharge me for something that I did not need. He also made some great recommendations for future work. Because of his level of service and my customer experience, I highly recommend Precision and will use them again in the future.
Garage door frames and mouldings will freshen up the appearance of your garage and garage door. We offer frames in a broad assortment of finishes and widths, so you can find the perfect fit for your garage. Update or repair the hardware on your garage door with our wide selection of our garage door parts and accessories. Some of the accessories we offer include cables, hinges, reinforcement brackets, and locking door handles.

Local Garage Door Repair, Inc is the best repairing company to pick. Besides, to get the real picture of Los Angeles CA, you can ask companions, neighbors and friends and family for suggestions.  Assess online audits from past clients and if conceivable, chat with them. Become more acquainted with how their involvement with the carport entryway repair business or individual was. Inquire as to whether we would inform you make utilization regarding the exceptionally same administrations. At the point when identifying the individuals who offer such services, it gets less complicated, to decide wisely on it is all about.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
While you may be able to increase efficiency by replacing the weather stripping at the bottom of an old garage door, the kind of insulation and energy efficient materials used in today’s new doors will make a drastic improvement on your garage’s energy efficiency. Just like the way a new garage door recoups its costs in increased home value, a new door will also quickly pay for itself in energy savings!
While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

Note the left winding cone with red spray paint. This shpritz of paint is applied to create fear and doubt in the mind of the do-it-yourselfer. Sometimes it is a color code for the wire size (using a DASMA standard, red indicating 0.2253 inch diameter wire). Sometimes it indicates the winding direction: red may indicate right-hand winding, but don't rely on that; do you own independent analysis. Sometimes it is a manufacturer's private code for another dimension than wire size. This color code is for the installer's information when the spring is new; I would not depend on interpreting the color code properly on an old spring, since one can't be certain of a correct interpretation without documentation from the original supplier.

Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Wood doors range from midprice to very expensive, depending on whether they consist of a lightweight wooden frame filled with foam insulation and wrapped in a plywood or hardboard skin (the least expensive) or are true frame-and-panel doors made of durable mahogany, redwood, or cedar. Wood doors usually carry a short warranty, perhaps only one year. 
Weight and cost: The 24-inch-long spring has a calculated weight of 8.4 lbs, not counting the winding cones. At less than $1/lb wholesale, and $3/lb retail for fabricated steel products, this spring should sell for about $8 to $25 (2005 prices) each, depending on the market and source. Since a pair is required, the expected cost for a pair is $16 to $50.
We are a family owned and operated company with local offices in various cities. We have offices in Arizona — from Phoenix to Tucson; Nevada— covering the entire Las Vegas metropolitan area, from North Las Vegas to Henderson; the Sunflower State of Kansas, from Wichita to Junction City; Wisconsin — spanning the entire Milwaukee county, from Fox Point to South Milwaukee; and Michigan, with our base in Sterling Heights.

Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.

J&S Overhead Garage Door Service also specializes in garage door opener repairs including broken gears, safety sensors, garage opener and chain adjustments and even remote and keypad replacements. Our technicians service major brands and carry necessary parts ad equipment parts on the trucks so you will never have to wait for a repair. If your opener can’t be repaired we do offer same day and same appointment professional installations offering several different garage door opener including chain and belt drive options.
Wood doors range from midprice to very expensive, depending on whether they consist of a lightweight wooden frame filled with foam insulation and wrapped in a plywood or hardboard skin (the least expensive) or are true frame-and-panel doors made of durable mahogany, redwood, or cedar. Wood doors usually carry a short warranty, perhaps only one year. 
Most importantly, you will be greeted by friendly staff and associates that will help you select the right garage door for your home. We welcome the opportunity to supply, install, and/or repair your garage door as well as answer any door questions you may have. When you choose us, you will quickly discover why thousands of Riverbend area customers from house to house and generation to generation have chosen Dan's Garage Door Service as their “DOOR KEEPER” for over 40 years.

Our team of 100-plus technicians and service representatives takes care of you every step along the way. Our technicians are the best in the area. They’ll provide expert guidance as you consider your options, and then top-notch service to complete the repairs. When you want Cincinnati or Northern Kentucky garage door repair you can trust, choose AE Door & Window.
Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.
The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit includes one 3-button compact remote one receiver one transformer and electrical wire (two-wire). The kit alleviates frequency issues from the recently implemented Land Mobile Radio communication system used by military bases as part of the Homeland Security efforts.  More + Product Details Close
×