Spring stretch: When the door is at the top of travel, the spring(s) are hardly wound, but are stretched, so on a single-spring installation this stretch tends to pull the shaft towards the non-spring side. With two springs, the stretch tends to cancel out. This top-of-travel spring stretch, being about 7 or 8 turns of the wire, will thus amount to upwards of about 2 inches on a typical size spring of 0.253 wire. This spreads out to a gap of about 0.020" per coil on a typical 100-coil spring, so the stretch is not very visible.
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
At Garage Doors & More, we are an authorized dealer for Pella, Amarr, Clopay and Haas Garage Doors. Feel free to check out our site to find the door that fits best for your home. In the top navigation bar there is a drop down. The garage doors tab is where you will find traditional garage doors. There is also another tab that will lead you to a page for our energy efficient garage doors. Other tabs include pages for our Carriage Garage Doors and Wood Garage Doors. You can also click the button below to see some of our special offers!

Garage door repair is a specialized job, which is typically handled by a garage door repair service. Professional garage door repair technicians can test or repair a garage door system and fix cosmetic blemishes on doors. Common requests include help with jammed or inoperable doors, slow or erratic doors, unusual sounds, dents or scrapes on the door, and general system testing. Garage door repair professionals can work on single-car, double-car and RV-size garage doors.


Since the springs are winding "up" when the door is closing and going down, the fully closed position is the most stressful on the steel and thus the most likely position at the moment of failure. This is a good thing, because failure near the top-of-travel means that you suddenly have a large, increasing weight falling. Thus we see the principle that you should never be standing or walking under the door when it is opening or closing, especially if you do so manually instead of with an electric opener. When the springs are working correctly, the door appears nearly weightless, but this is an illusion that turns into a calamity when the springs suddenly fail.
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
As noted above, set-screw clamping may have distorted the cross-section of the shaft and made it difficult to slide off all the hardware. With the shaft on the floor, it may be possible to restore enough roundness to proceed, using compensating clamping force to the distorted area via a machinist's vise, an arbor press, a hydraulic shop press, etc., on the shaft body. Burrs and other slight distortions on the shaft can be filed off with a hand file or touched with an abrasive wheel on an angle grinder. At some point, the condition of the shaft may just be degraded enough that it ought to be replaced.
Are you needing garage door repair? Has your garage door opener stopped working, or are you looking to boost your curb appeal? Whatever your garage door need may be, your local authorized Overhead Door™ Distributor is there to assist. You can find the nearest Overhead Door™ Distributor near you today by using our Distributor Locator​ to search your area. ​​
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.

These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.


J&S Overhead Garage Door Service also specializes in garage door opener repairs including broken gears, safety sensors, garage opener and chain adjustments and even remote and keypad replacements. Our technicians service major brands and carry necessary parts ad equipment parts on the trucks so you will never have to wait for a repair. If your opener can’t be repaired we do offer same day and same appointment professional installations offering several different garage door opener including chain and belt drive options.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Appliance Repair Tulsa, OK 1600 Miller Trunk Hwy Appliance Repairs 1400 N Parham Rd Appliance Repairs Freehold Appliance Repair Kahului Maui Appliance Repair Appliance Repair in Clovis Eureka, CA Appliance Repair 2800 N Germantown Prkway Appliance Repairs 7700 E Kellogg Dr Appliance Repairs Appliance Store Melbourne Appliance Store Victoria Appliance Repair in Fort Worth Appliance Repair Puyallup, WA 10 W Lake St Appliance Repairs Appliance Repair in Arlington Appliance Repair in Frisco Saint George Appliance Repair Appliance Repair in Cedar Park Appliance Repair in Elizabethtown
The various increments of standard wire sizes differ by only about 0.010 inch, so calipers or a micrometer would be the tool to use to be certain of the stepped size you have, or else a trustworthy ruler marked in tenths of an inch to use the measure-10-turns-and-divide-by-10 trick. The most common wire sizes in the US are 0.207", 0.218", 0.225", 0.234", 0.243", 0.250", and 0.262".
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
The best garage door openers can be controlled from a remote location through your phone. If you’ve ever left home and had a moment of panic, not knowing if you left the garage door open, this feature can give you peace of mind. The door opener’s built-in Wi-Fi connects directly with your home Wi-Fi router, which allows you to close your garage door from wherever you are through a MyQ smartphone app. The Chamberlain Group opener has this feature – it’s a 1-horsepower garage door opener with extra lifting power for unusually heavy doors of over 500 pounds.

This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.

However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.

If the spring is broken near a winding cone, you might think you can remove and discard the short broken piece of spring from the cone, clean up the end of the long remaining spring, and insert that end into the cone. This is another extrememly risky improvisation. The shortened spring is not going to have the correct weight-bearing characteristics for the door, so you will not be able to balance the door properly. The shortened spring will be proportionately overwound, resulting in extra stress that will increase the expectation of another fracture. And the aging and history of the original spring being broken greatly increases the likelihood of another fracture at other locations.
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 
Though we’ve grown a great deal, we still approach each customer with a focus on personalized service. We want to meet your needs as effectively as possible. We also provide a sense of urgency to each job, knowing that garage door needs often represent a significant life or work slowdown. Get in touch with us to schedule a visit, ask questions or to learn more about what we offer and how we can help get your garage door back up and running again.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
“Especially on houses where the garage is front and center, the garage door absolutely has to look good,” says Casey McGrath, a real estate practitioner in Kitsap County, Wash. And it has to operate smoothly: Americans use the garage more than any other entry to the house, including the front door, according to a survey commissioned by window and door manufacturer JELD-WEN.

We also Specialize in frayed and broken garage door cables. Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system. Systems serviced include Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion garage door spring systems on the spot.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.
Horsepower: The horsepower measurement, often shortened to HP, describes the power the garage door opener motor has. A motor with a greater horsepower measurement will open and close the door more quickly, while also being able to handle larger and heavier doors. Motors between 1/2 HP and 1 HP are the most common for residential garages, FeldCo says.
Here are the new replacement springs I ordered from a distributor, which I found using a Google search for "garage door supply" (search that phrase now). You certainly won't find these at Home Depot or Lowe's (although last I checked Lowe's does carry the less daunting extension spring replacements). I also have a list of some suppliers at the end of this page.
Leveling the door: Before commencing the spring winding, to check that you have the door properly leveled on the cables, considering all the factors above that make this a tricky adjustment, apply the winding cone setscrew lightly to lock the (unwound) spring cone temporarily on the torsion shaft, and momentarily lift the door slightly off the floor. Adjust the drum set as needed to level the door, repeating this slight lift test. Loosen the cone setscrew before winding the spring(s).
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.

Garage Door Repair

×