If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
In each of our branches, we have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
I make no recommendations of, and have no connection to, any of the following suppliers. These are just those whom I have learned about from my Web searches, from correspondence with those sending email about their experiences, or directly from the suppliers. I have removed several contacts that were generating complaints to me from dissatisfied customers. I have added this list to this page due to all the email queries I was receiving daily asking where to obtain parts. If you are a supplier and would like to be added to the list, see my email address at the end of this page.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
Our knowledgeable, dependable and friendly team of professionals can work closely with you to select, design and install a quality garage door that best serves your daily needs, enhances the architecture of your home and fits your budget. The extensively trained and experienced technicians at Kitsap Garage Door can help you with any of your garage door service needs, large or small, and are ready to repair any garage door make or model.
We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.

Garage Door Opener Company


Permits must be applied for when you are building a new home or structure. This permit will cover the building of the structure and cover the inspection for your garage door. The inspection process for a new door is pretty simple. The county will want to make sure that you have a garage door installed that meets local wind rating standards. In Mecklenburg County, that standard is 90 mph. That means that your door must be rigid enough to withstand 3 second gust by winds of up to 90 miles per hour.
Dodging a falling door:: Reversing this equation gives us x=gt^2/2 as the fallen distance x for a given time t. How much time would you have to dodge a falling door if the spring were to suddenly break at the top of travel? Let us assume you are 5.5 feet tall, so the door will hit your head after falling 2 feet from its 7.5 foot fully-raised height. This 2-foot fall takes sqrt(2*2/32.2) = 0.35 seconds (350 milliseconds). The quickest human response time is about 200 milliseconds, so even if you are alert to the hazard, this leaves you only about 150 milliseconds to accelerate and move your noggin out of the way. If you are an Olympic gold medalist in the 100 meter dash, you can accelerate (horizontally) about 10 feet/second^2, and your 150 milliseconds of wide-eyed panic will move you all of 10*0.15^2/2 = 0.11 foot = 1.35 inch.

Just compare our total price—item price + tax (if applicable) + shipping&handling—to the total price of other Online stores. If you find a lower price, we will match the price and refund 10% of the difference. Call us at 1-877-357-Door (3667) today with your quote from a competitor. We will review the lower price while processing your order and make any necessary reductions before your order ships.


Your garage door is most likely the largest opening on your home, and as a result, it can affect your home’s energy efficiency. For homes in areas that experience colder winters or warmer summers, choosing an insulated door can save you money and improve the comfort of your home. Doors insulated with our Intellicore® insulation technology operate more quietly and are more durable. We also offer insulated glass window options that can help maintain energy efficiency and allow natural light into your garage. Visit our insulation guide to learn more about garage door insulation, or learn more about Intellicore® here.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.

This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
Although you can replace your garage door opener on your own, it’s more difficult than most DIY projects, so following the installation instructions is a must. If you’re not confident you can replace the opener on your own, you should consider hiring a professional, which further increases your costs. You can also expect to pay more if you’re replacing a garage door in addition to the opener.
Horsepower is another key factor when it comes to garage door openers. Look into ½ horsepower garage openers if you have standard aluminum doors. Oversized doors and one-piece doors may require 3/4, 1 or 1¼ horsepower garage door openers. Garage openers with higher horsepower use less effort to operate and minimize wear and tear on the motor. This is ideal if your garage doors act as the main entrance to your home.
If this manipulative, we-are-your-nanny business approach is truly in our best interests as consumers, then we shouldn't be allowed near ladders, lawn mowers, or power tools. Those products are just as hazardous and prone to misuse as torsion springs, yet no one thinks of them as forbidden. The only genuine difference is that torsion springs are a hazardous thing you need only rarely, while a lawn mower is a hazardous thing you need all the time.
It’s important to pick a door that suits the style of your house. If you live in a Craftsman bungalow, for example, you might want something that looks like the swing-out doors found on garages behind early Craftsman houses. Manufacturers of modern roll-up doors make them in styles that mimic the old swing doors, complete with faux strap hinges on the sides and a pair of handles flanking a deep groove in the center. 

Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
We want to serve you not only today, but also in the years ahead. To do that, we make sure that we provide prompt, professional, well-trained technicians that efficiently get the job done right the first time. We take pride in doing everything possible to eliminate warranty issues and to ensure that our clients are thoroughly pleased and return to us for all garage door needs.

When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.
The deluxe-model upsell trick: Don't you want the best? Don't you want to protect your family? Galvanized springs may be offered to you at extra expense as "longer lasting". Although bare springs (also called "oil tempered") can develop a light film of rust, the eventual failure is due to fatigue and not corrosion. The use of coated springs (whether galvanized, painted, powder-coated, or surface-converted) is mostly about appearance: the customer likes his new door to look shiny, and the customer doesn't like repair parts that show superficial rust from storage.
Here's a view of my door and its broken torsion spring. This door is 10 feet wide and 7 feet high, constructed of 3/4 thick hollow wood panels inside with 3/4 inch plywood siding outside to match the house exterior. This is original to the house which was constructed in 1978, and is much heavier (238 pounds, as I measured later as described below) than the steel doors most common today in new construction. The 10-foot width is a little larger than usual for a one-car garage; such doors are typically only 7 or 9 feet wide. The ceiling height is 9 feet, providing 18 inches clearance above the torsion shaft. This is in a 3-car garage with 3 separate extra-wide doors. Every man's dream! ('cept when the door is broke.)
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
In 1921, C.G Johnson invented the upward-acting garage door and revolutionized the way the world entered their homes. For more than 97 years, Overhead Door™ garage doors have been securing and providing families access to their homes. Overhead Door™ garage doors are assembled in the United States and sold at over 450 authorized Ribbon Distributors throughout North America. The Overhead Door™ brand and Overhead Door™ distributors are synonymous with quality and dependability. To ensure you are getting the genuine, the original, make sure to always look for the Red Ribbon.
×