The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit includes one 3-button compact remote one receiver one transformer and electrical wire (two-wire). The kit alleviates frequency issues from the recently implemented Land Mobile Radio communication system used by military bases as part of the Homeland Security efforts.  More + Product Details Close
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.

Garage Door Service Co


If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
Another moment of truth arrives as the winding-up of the springs begins. (I am just posing here with the camera held out in my left hand. Except for lifting the door onto the scale, this was a one-man job, including the photography.) The position of the bars in this photo was necessary to take the photo, and does not show a correct winding technique, You should not have to swing the bar up as high over the top as shown. The lower bar during winding should swing from pointing down to pointing a little past horizontal. Then you hold that bar horizontal while socketing the other bar pointing down, apply force to that (now) lower bar, then remove the (now) upper bar, wind one-quarter turn, and repeat.
First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.

Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.


Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
A rolling code is a protocol used by garage door openers to keep your door safe and secure. When the radio signals from your remote control are broadcast to your garage door opener, it uses a specific code to communicate. Older models used the same code every time, making garage door openers vulnerable to burglars using a radio frequency identifier device. 
Establish an alternate entry to your garage or update an existing one with our selection of garage entry doors. With an entry door, you will lose less heat or air when you enter your garage to work. Our variety of garage and outdoor organization materials will help you keep all the items in your garage neatly and efficiently organized while our floor coatings and utility flooring will help ensure your cement garage floors last longer than if they were left untreated.
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 
Establish an alternate entry to your garage or update an existing one with our selection of garage entry doors. With an entry door, you will lose less heat or air when you enter your garage to work. Our variety of garage and outdoor organization materials will help you keep all the items in your garage neatly and efficiently organized while our floor coatings and utility flooring will help ensure your cement garage floors last longer than if they were left untreated.

Furthermore, newer doors come with more improved security features, helping to improve the way you protect your home and loved ones. While older doors are easy to break into, whether through breaking the lift mechanism or even using a universal garage door remote, new doors come with many redundant security features, which will go a long way in deterring even the most ingenious burglar.
Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
Over the past 15 years, we've been providing professional garage door repair and services to families across the Lehigh Valley and Western New Jersey. We're a family-owned business, and we treat every customer as if they are family as well. We pride ourselves on our dedication to exceptional service. If you are having an issue with your garage door, we can help! We service ALL makes and models of garage doors and openers. Whether you need a repair, a replacement, or routine maintenance, you can rely on us to get the job done at an affordable price.
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.
×