One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.
One might stack lumber or arrange some other low platform for a steady footing, instead of the ladder. The aluminum ladder shown here is the splendid 16-foot Krause Multimatic, which carries a Type 1A Industrial rating (300 pound working load); I highly recommend it. However, product liability apparently forced this company into bankruptcy in September 2000 and the company ceased operations in June 2001; see http://www.krauseladders.com (this Web site went dead sometime in mid-2002). The world is a dangerous place.

By watching the chalk mark while winding, you can count the number of turns applied, and confirm the number later. My standard-size door (7 foot height) with 4-inch drums has a nominal wind of 7-1/4 or 7-1/2 turns, which leaves 1/4 or 1/2 turn at the top-of-travel to keep the lift cables under tension. After 7 turns on the first spring, I clamped down the set-screws, weighed the door again, and found a lift of about 100 pounds in reduced weight. As expected, this wasn't quite half of the full 238 pounds, nor would it leave any torsion at the top-of-travel, so I added an 8th turn. The door now weighed 122 pounds on one spring, which was ideal. After winding the other spring, the door lifted easily, with only a few pounds apparent weight. This confirmed that the spring choice was properly matched to the door design. I engaged the electric opener trolley, and adjusted the opener forces down to a safer level suitable for the new, improved balance. The door was now ready for return to service.
Since 1975, Kitsap Garage door has provided Kitsap Penninsula with reliable, comprehensive and responsive residential and commercial garage door repair, maintenance and installation services. At Kitsap Garage Door, our primary focus is offering Bremerton, Shelton and Kitsap, WA, home and business owners with the highest quality products and services, as well as exceptional customer experiences marked with free service estimates, workmanship warranties, reliable support and emergency services.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
Direct Drive - Unlike chain- and belt-driven systems, where the motor remains stationary while moving a chain, a direct drive motor moves while the chain stays in place. Because of this, the only moving part is the gear the motor uses to move while lifting the door. To our knowledge, only one company makes direct drive garage door openers: Sommer. The company claims the motors are more efficient and quieter than any other type of opener. However, this is the most expensive type of opener we’ve found, costing around $286 on average.

We strive to deliver the most relevant products, services, and guidance to provide you with customized and flexible solutions to meet your specific requirements and budget. Choosing us means that you will not be disappointed. We provide round-the-clock reliable garage door repair, garage door service and support in Orange County, CA. Champion Garage Door Repair is, therefore, your household name when it comes to garage doors and garage door repair service.


A spring design manual, also called a rate book, gives tables that relate the torque constant ("rate") and maximum turns for springs of given wire size, diameter, and length. For example, a typical page in a rate book would show a table for a given wire size and inside diameter, the maximum inch-pounds (MIP) of torque available for a standard lifetime of 10,000 cycles in that size, the weight of the spring per linear inch, and the rates of the spring (as IPPT, inch-pounds per turn) for each of various lengths. From these figures one can calculate the lifting capacity, substitutions, conversions, and cycle life upgrades for a door of given weight and drum geometry. The weight-lifting capacity of a given spring is calculated based on its torque constant (IPPT, or inch-pounds per turn), which is the rotational version of the spring constant that characterizes the spring. The IPPT constant is found from tables giving IPPT for given spring dimensions (wire-size/diameter/length). The same tables may indicate the maximum number of turns for various expected lifetimes in cycles. The torque required to balance a given door can be calculated from the weight of the door times the moment arm of the drums (as we do below under "Calculating the Forces We Will Be Handling"). The ultimate torque of the spring in the fully-wound condition is the number of turns (when fully-wound) times the IPPT constant. Choosing a spring to balance the door then simply requires matching the ultimate torque of the spring to the balancing torque.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
It can be very problematic if one's car doors are not fitted properly. The garage is the place where people house their cars with a lot of safety and security and it is only natural that they would want the very best for their doors. With the increase in burglary and other anti-social activities, it has become all the more important to take the necessary step towards building a strong garage with reliable door opener. At Larry Garage Door, we try to do this with the most efficient staff who are dedicated towards serving their clients and give them a door at an accessible price. We have made sure that whichever type of garage our client might have, they will find the right door and opener with us. We have years of experience with us and we have worked with clients all over the California's Central Valley. We only use the best aluminum and steel if their preference is more towards the metal doors, and also giving a very low price to our clients.
We take the garage door installation process very seriously. The way a garage door is installed will impact every aspect of it for years to come. The noise level, ease of use, wear on other parts, appearance, and even out of pocket repair costs over the life of the garage door are all a direct result of how well the installation was performed. Call us today and you will see firsthand the A1 difference. Years from now you will be happy you chose A1!

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
The Heavy Duty Chain Extension Kit for 8 The Heavy Duty Chain Extension Kit for 8 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 8 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
aluminium frames B&D B and D doors and openers BnD Colorbond Custom garage doors cyclone Danmar Doors Garage door insulation garage door insurance garage door motors garage door remote garage door repairs garage door seals garage doors perth garage door springs and cables garage door struts insulated garage doors keyless entry Knotwood lifting cables Merlin garage door motors Merlin garage door openers Perth perth garage door repairs perth garage doors perth garage door servicing replacement remote reprogram garage door remote roller doors sectional garage doors Steel-Line tension springs tracks and rollers wind struts
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!

When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

Garage Door Service

×