Charlotte, NC is  a bustling market for new homes, business construction and restoring old homes.  Charlotte’s real estate market is booming. Our company has been a part of this growth by installing and repairing over 50,000 garage doors since 2001. In this span of time, we have had no issues with the county inspections office. We have done this by making sure that our clients buy the right doors, and have permits in place, if needed. Keep in mind that we are not general contractors, so we do not supply permits, but we provide the information and resources for you to easily apply for permits if one is needed for your project.


The prior clamping of the set-screws tends to have pressed a dimple into the hollow shaft and to have distorted the shaft's roundness into an eccentric shape. While releasing the set-screws, I was careful to loosen them enough to let the cone swing around any such distortions. I was also careful to observe any binding of the old cones on the eccentricity or burring on the shaft. The fit of the cone on the shaft is supposed to be loose enough to avoid binding, but if it were to occur one would have to be careful not to assume the spring was unwound when in fact the cone was just stuck on the shaft. If I had a stuck cone that I could not unwind with a little extra force, then I would have called in a technician to deal with it. In the worst case, I suppose the spring must be deliberately broken with some hazard, thus releasing it for a forceful disassembly, and the shaft and some other parts replaced. But this is an unlikely situation and in this case was not necessary.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
Speed of a falling door:: Physics tells us that the transit time of a free-falling body is sqrt(2x/g), where x is the length of the fall and g is the acceleration due to gravity (32.2 ft/sec^2). If this typical 150 lb door were to fall an equivalent of 3.75 feet, this falling time would be sqrt(2*3.75/32.2) = 0.48 seconds (480 milliseconds). The terminal velocity is gt, or 0.48 seconds * 32.2 ft/sec^2 = 15.5 ft/sec = 10.6 mph.

Since their invention in the 1920s, electric garage door openers have come a long way. Garage door openers work by using a trolley connected to an arm that attaches to the top of the garage door and slides back and forth on a track, which opens and closes the garage door. When operating the motor, a chain or belt turns and pulls the trolley along the track. A good garage door opener will have a horsepower of 1/2 HP, 3/4 HP, or 1-1/4 HP. Garage door openers have the ability to open and close a limited number of times in power outage emergencies. Security is something else to consider when purchasing an opener. It's helpful to have sensors that will stop the operation of the garage door when a person, vehicle, or other obstacle is in the way.

Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
Garage door frames and mouldings will freshen up the appearance of your garage and garage door. We offer frames in a broad assortment of finishes and widths, so you can find the perfect fit for your garage. Update or repair the hardware on your garage door with our wide selection of our garage door parts and accessories. Some of the accessories we offer include cables, hinges, reinforcement brackets, and locking door handles.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.

We also Specialize in frayed and broken garage door cables. Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system. Systems serviced include Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion garage door spring systems on the spot.

Once the springs are torqued, the setscrews tightened, and the locking pliers and winding rods removed, do not play with turning the torsion bar using the winding rods. Doing so even momentarily can relieve the tension on the lift cables, which then easily slip off the drums. Replacing the cables on the drums can be difficult without repeating the entire spring unwinding-winding procedure again, and the cables can be damaged if tension is applied while they are off the drums.
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
Disclosure: This post is brought to you by the Insider Picks team. We highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We operate independently from our advertising sales team. We welcome your feedback. Email us at [email protected]
In 1992 the United States Consumer Product Safety Commission released new rules for automatic garage door openers. Anything manufactured after 1993 was required to include either an electric eye (a pair of sensors that detect an object obstructing the doorway) or a wall-mounted control button that users hold down in order to close the door entirely. Most manufacturers opted for the electric eye method, sometimes referred to as safety sensors.
Whether you’re looking for garage door opener maintenance, garage door opener repair, or a brand new garage door opener, Sears Home Services can help. We’re your best, most-trusted option for fast, quick, and easy local service, repair, and maintenance of your automatic garage door opener. Whether your garage door won’t open or close, your garage door opener chain is broken, your automatic garage door opener won’t work after a power outage, your garage door won’t work when it’s cold, or your automatic garage door opener won’t stop running, we’ll connect you to the best local automatic garage door opener repair service technicians in the business. Technicians that are highly trained, licensed, vetted, nearby, and guaranteed to help fix all of your garage door opener needs. We have thousands of local technicians that are always “near me,” that can help you no matter what your appliance emergency.
When a garage door goes off the track, the spring breaks, the door is dented or the garage door opener is on the fritz, a professional garage door repair specialist can help. The cost to have a garage door fixed varies, but the national average cost of garage door repair is $70-$110. The extent of the damage and the size and material of the door will affect the final cost. A garage door repair company generally charges a national average of $80 for a service call, which includes the first hour of labor and service, such as testing and inspecting the garage door and opener. Apart from labor, the garage door repair costs hinge on buying replacements parts. For example, a new spring costs an average of $60. Expect to pay several hundred dollars, though, if the door is beyond repair; a new garage door ranges in price from $200 to $4,000, and most homeowners spend an average of $800-$1,200.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
The one excuse that makes the most sense is, "if we sell springs to a do-it-yourselfer, and he gets hurt installing it, we could get sued." I can sympathize with someone who wants to sell only to the trade and not bother with the risk of a spurious product liability lawsuit from an ignorant member of the public. But the lawn-mower dealers have figured out how to manage that kind of exposure, so this is not an absolute barrier to retailing garage door parts to the public. It doesn't explain why torsion springs at retail are virtually non-existent.
You might be thinking: Aha! Why don't we lift the door, clamp it in place, and install the springs while they are thus safely unwound, rather than deal with all that accumulation of hazardous torque? The answer: At the top-of-travel, the unwound springs are not fully relaxed; they are still clamped to the torsion shaft with a significant stretch along the shaft axis, plus about a half-turn to keep the door snug at the top. This extra length amounts to the stacking of extra turns that accumulate from winding, also termed "spring growth" in the business. In my case this is about 7 turns of 0.2253 wire, or about 2 inches. Stretching the spring that much and clamping it with a half-turn or so of twist is not feasible.

Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.


Whether you're looking for the beautiful " Carriage House" style that adds beauty to your home, an energy efficient door that keeps your home warm or cool while reducing energy bills, or just needs a Custom Garage Door we've got a model that fits your needs. Learn more here.. Or come visit us at our new showroom to check out 25+ door models in person.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers.  It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.

Garage Door Repair Company

×