The material and style of your door as well as the replacement parts needed will impact the total cost of your project. It would cost less to install a steel door with no opener then it would to install a wood door with an opener etc... High tech doors come with enery-effecient glaze and thick insualation as well as finshed interiors and other upgrades. These doors are more expensive but are more reliable and durable.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Most doors come with electric door openers. After a while these openers malfunction and need to be replaced. If your opener is broken, you're in luck. These repairs don't cost very much and can be replaced easily. You might even be able to do it yourself. Learn how to replace your garage door opener in 15 minutes https://www.youtube.com/watch?v=HeaR6Yhx6IY.
Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.
We lead busy and sometimes hectic lives. It's easy for someone low on sleep and high on stress to accidently bump into their garage door leaving a little damage. If you're lucky it's just an individual garage door panel that's been damaged. This will leave you with the option of garage door panel replacment. There's a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you've got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you'll end up having to just replace the entire door. Many times it's actually easier and more cost effective to just replace the garage door.

Garage Doors & More of the Piedmont has been serving the Charlotte Metro area since 2001. At last count, we have serviced nearly 30,000 residential homes in the Charlotte area. Our commercial department also has nearly 1,000 customers. We have been so successful because of our goal to provide the best prices and service available. See our special offers page to see our most popular offers coupon offers.

It’s important to pick a door that suits the style of your house. If you live in a Craftsman bungalow, for example, you might want something that looks like the swing-out doors found on garages behind early Craftsman houses. Manufacturers of modern roll-up doors make them in styles that mimic the old swing doors, complete with faux strap hinges on the sides and a pair of handles flanking a deep groove in the center. 
For fast service and great prices in the Charlotte area, call Garage Doors & More. We have the area’s best trained technical staff, and all have been 3rd party certified. We top that off with our $29.00 Service Call with repair. We repair all brands of garage doors and openers. We also stock many hard to find parts. We have multiple locations in the Charlotte Metro area, so rest assured that we can get a technician to your home or business as quickly as possible. Call us today for fast service.
We strive to deliver the most relevant products, services, and guidance to provide you with customized and flexible solutions to meet your specific requirements and budget. Choosing us means that you will not be disappointed. We provide round-the-clock reliable garage door repair, garage door service and support in Orange County, CA. Champion Garage Door Repair is, therefore, your household name when it comes to garage doors and garage door repair service.

Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
But the insulation won’t save energy unless you heat the garage or treat your attached garage as part of the “conditioned” part of your house. The federal Energy Star program recommends against doing this if you park cars, store lawn chemicals, or use solvents there because it could let dangerous fumes inside; it’s better to insulate only the shared wall and use that as the indoor-outdoor boundary.
But the insulation won’t save energy unless you heat the garage or treat your attached garage as part of the “conditioned” part of your house. The federal Energy Star program recommends against doing this if you park cars, store lawn chemicals, or use solvents there because it could let dangerous fumes inside; it’s better to insulate only the shared wall and use that as the indoor-outdoor boundary.
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path. [12][13]
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.
Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.
Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.

Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.
Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system including Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion setups on the spot.
We strive to deliver the most relevant products, services, and guidance to provide you with customized and flexible solutions to meet your specific requirements and budget. Choosing us means that you will not be disappointed. We provide round-the-clock reliable garage door repair, garage door service and support in Orange County, CA. Champion Garage Door Repair is, therefore, your household name when it comes to garage doors and garage door repair service.
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.

Your garage door is most likely the largest opening on your home, and as a result, it can affect your home’s energy efficiency. For homes in areas that experience colder winters or warmer summers, choosing an insulated door can save you money and improve the comfort of your home. Doors insulated with our Intellicore® insulation technology operate more quietly and are more durable. We also offer insulated glass window options that can help maintain energy efficiency and allow natural light into your garage. Visit our insulation guide to learn more about garage door insulation, or learn more about Intellicore® here.
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.
Right-hand versus left-hand winding: Springs are chiral, that is, wound or "laid" in either a left- or right-hand orientation. This is a critical property of their design and specification; you cannot substitute a left for a right or vice versa. If you were to grasp the spring in your hand, and if your right hand orients the tips of your fingers like the ends of the coiled wire when your thumb points "out" of the core of the spring, then you have a right-hand spring; likewise left (which end you grasp does not matter). (This also happens to match the "right hand rule" of magnetic polarity, if you happen to be knowledgeable in such esoteric subjects.) Another way to identify the winding is to examine the spring vertically in front of you; if the coils facing you rise going to the right, it is right-hand (thus you can remember, "rise to the right is right-hand"), and likewise left indicates left-hand. Another way is to view the coil axially; a right-hand spring winds in a clockwise direction as it recedes away, and a left-hand spring counter-clockwise. Yet another way, not so easy to remember, is to hold the spring vertically and compare the coil shape to the letter "Z" (indicates right-hand lay) or the letter "S" (indicates left-hand lay).
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.

Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.
Are you needing garage door repair? Has your garage door opener stopped working, or are you looking to boost your curb appeal? Whatever your garage door need may be, your local authorized Overhead Door™ Distributor is there to assist. You can find the nearest Overhead Door™ Distributor near you today by using our Distributor Locator​ to search your area. ​​
×