Note the left winding cone with red spray paint. This shpritz of paint is applied to create fear and doubt in the mind of the do-it-yourselfer. Sometimes it is a color code for the wire size (using a DASMA standard, red indicating 0.2253 inch diameter wire). Sometimes it indicates the winding direction: red may indicate right-hand winding, but don't rely on that; do you own independent analysis. Sometimes it is a manufacturer's private code for another dimension than wire size. This color code is for the installer's information when the spring is new; I would not depend on interpreting the color code properly on an old spring, since one can't be certain of a correct interpretation without documentation from the original supplier.
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.

Garage Door Service Co


We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.

What is a battery backup? During a power outage, a battery backup allows your garage door opener to keep working. This is especially important when a wildfire is blazing. During the infamous California wildfires, many people were getting trapped in their garages. Several even died. California state Senator Bill Dodd was among those unable to get out, since he could not manually open his heavy wooden garage door. Drawing on his personal experience, Senator Dodd introduced a bill to make battery backups mandatory in the state of California. On August 16, 2018 the Garage Door Safety Bill passed with wide bipartisan support. As Cheryl Diehm, a Santa Rosa resident who testified before lawmakers, put it, "Make no mistake -- this legislation will help save lives."

Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.

Since the springs are winding "up" when the door is closing and going down, the fully closed position is the most stressful on the steel and thus the most likely position at the moment of failure. This is a good thing, because failure near the top-of-travel means that you suddenly have a large, increasing weight falling. Thus we see the principle that you should never be standing or walking under the door when it is opening or closing, especially if you do so manually instead of with an electric opener. When the springs are working correctly, the door appears nearly weightless, but this is an illusion that turns into a calamity when the springs suddenly fail.
One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
This page is a description of how I replaced torsion springs on a garage door. You may find that my experience either frightens you from trying such a stunt yourself, or encourages you to give it a try. You may curse me for revealing the techniques supposedly known only to the trade, or perhaps thank me for explaining how it's done. All the secrets are revealed below. Even if you hire this work out, just knowing how it is done will help you shop for the best deal and avoid falling prey to overcharging tricks.
Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.
Note the left winding cone with red spray paint. This shpritz of paint is applied to create fear and doubt in the mind of the do-it-yourselfer. Sometimes it is a color code for the wire size (using a DASMA standard, red indicating 0.2253 inch diameter wire). Sometimes it indicates the winding direction: red may indicate right-hand winding, but don't rely on that; do you own independent analysis. Sometimes it is a manufacturer's private code for another dimension than wire size. This color code is for the installer's information when the spring is new; I would not depend on interpreting the color code properly on an old spring, since one can't be certain of a correct interpretation without documentation from the original supplier.
 The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more 

The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.

Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and

Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.

With all the styles offered by Clopay®, many homeowners fall in love with multiple doors. To help you choose the best garage door for your home, Clopay® has developed a comprehensive buying guide, outlining styles, construction materials, insulation, wind resistance, automatic garage door openers and more. We also allow you to view different door styles on your home with our Door Imagination System. Simply upload your home or choose from a variety of sample homes with one-car, two-car, and three-car garages to design the best garage door for your home.
Our customer loyalty is not necessarily tied to just product quality, brand recognition, and service excellence. While those things matter, our customers place significantly greater emphasis on satisfaction with the sales experience itself when committing to Direct Garage Doors. Within the sales experience, our customers learn new ways to reduce operating expenses with our green products.
My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.
Spring stretch: When the door is at the top of travel, the spring(s) are hardly wound, but are stretched, so on a single-spring installation this stretch tends to pull the shaft towards the non-spring side. With two springs, the stretch tends to cancel out. This top-of-travel spring stretch, being about 7 or 8 turns of the wire, will thus amount to upwards of about 2 inches on a typical size spring of 0.253 wire. This spreads out to a gap of about 0.020" per coil on a typical 100-coil spring, so the stretch is not very visible.
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.

Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.


Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.
Depending on the type and location of the damage you might have an alternative to replacing panels, or entire garage doors. One solution to give new life to your garage door is repair. Small dents, rot, rust or holes can be repair without replacing. Depending on what wrong with the panel, average prices for repair are $130 for steel door repairs, $190 for wood, $170 for aluminum and $150 for fiberglass. Garage door panel repair can save homeowners money, but should be weighed against garage door panel replacment.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
Here's a view of my door and its broken torsion spring. This door is 10 feet wide and 7 feet high, constructed of 3/4 thick hollow wood panels inside with 3/4 inch plywood siding outside to match the house exterior. This is original to the house which was constructed in 1978, and is much heavier (238 pounds, as I measured later as described below) than the steel doors most common today in new construction. The 10-foot width is a little larger than usual for a one-car garage; such doors are typically only 7 or 9 feet wide. The ceiling height is 9 feet, providing 18 inches clearance above the torsion shaft. This is in a 3-car garage with 3 separate extra-wide doors. Every man's dream! ('cept when the door is broke.)
To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust.

Some of the best garage door openers offer special features like a backup power source or a timer that automatically closes the door behind you at a predetermined time. While the door openers we reviewed vary in terms of power, noise and efficiency, they are all effective in the all-important task of letting you come and go with the simple push of a button. Here are the criteria we used to rank the top garage door openers:
Measure springs only when relaxed: Measurements must be taken on a relaxed spring because the winding adds significant overall length while reducing the coiled diameter. If you have a paired design, and one is broken and one is intact, then don't try to measure the length of the intact spring with the door down. A wound spring has 7 or 8 turns adding to the overall length, and will therefore be about 2 inches longer than when relaxed. Measure the lengths of the pieces of the broken spring, which will be unwound, and add them together. As a check, one can measure the length of the intact spring after it is unwound in the procedure to follow below. Be sure also to observe whether the springs are originally of equal sizes, because it is quite possible that they are not.
Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.
Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.
Winding "up" starts out easy. It finishes at the proper number of turns, by which time you are pushing against the maximum torque. Count the turns of spring winding from when the springs are slack. To be sure you're winding the right direction, all you have to remember is that proper winding makes the spring smaller in diameter and longer in length as it twists "in". On the standard door (most common), this means you push the winding bars up to wind up the spring, which is an easily remembered rule. This is very apparent and should be verified during the first few easy turns. You can also think about the correct winding direction in mechanical terms, namely which way the reaction of the spring will torque the shaft and drums, which in turn will lift the cable. This should all make perfect sense before you attempt the manipulations.

R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Reduce your monthly energy bill with insulated garage doors. They feature an insulated core made of polystyrene that’s surrounded by a steel cover. This can help you maintain the temperature inside your home no matter if it’s extremely hot or cold outdoors. Insulated garage doors are also known for their quiet operation. Be sure to look at the insulation rating – or R-value – when considering garage doors. The higher the R-value, the better the insulation.
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
Started in 2004, Aladdin Garage Doors has become known nationwide as the trusted source for garage doors, repairs, and fast, efficient service. With a mission focused on delivering outstanding customer care, we’re proud to offer garage doors that lead the industry in quality, value, and lifetime protection for homes and businesses. Whatever your garage door needs may be, you can count on Aladdin Garage Doors to offer:
Here are the new replacement springs I ordered from a distributor, which I found using a Google search for "garage door supply" (search that phrase now). You certainly won't find these at Home Depot or Lowe's (although last I checked Lowe's does carry the less daunting extension spring replacements). I also have a list of some suppliers at the end of this page.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.

Beware of improprer prior installations: Sometimes the existing door installation is not correct, and the old springs should not be used as a specification for replacements. For example, the old springs might have been replaced with incorrect sizes because the last repairman didn't have the right one on his truck. If your door has never worked quite right, something like this might be the cause. To correct this, you must use the weight of the door to specify the spring, either from a spring rate manual giving spring torque constants, or from the formulas below.
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!
×