The "liability" angle: The flip side of "safety issue" is "liability". This is not used to directly sell you something; it is used to demean the cheaper alternative and prod you into buying a more expensive (and profitable) option. For example, you may be pressured into buying a whole new door, when you just need a new spring, by the salesman telling you he can't just replace the spring due to "liability" issues. Since product liability is a big burden on the garage door industry, and so many old doors (and especially automatic openers) are dangerous, this may be a genuine reason to accept a higher price.
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.
Uncentered center bearing plate: The center bearing plate need not actually be in the center. It doesn't much matter where it is, since the purpose of the bracket is to anchor the spring ends. This anchoring must be secure, since all the torsion is held together at that point. On a stud-framed wall, this bracket may be placed over the stud closest to the center rather than exactly at the center of the door opening.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
Thanks for considering our wide array of Overhead Door™ residential, commercial and industrial doors, openers, operators and accessories to complete your home, business or remodeling project. We are confident that you will find a door and opener product to meet your needs. After all, we lead the industry with our comprehensive selection of residential and commercial door systems. Overhead Door Corporation is a proud member of DASMA.
The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit The Genie Universal Dual Frequency Remote Conversion/Upgrade Kit includes one 3-button compact remote one receiver one transformer and electrical wire (two-wire). The kit alleviates frequency issues from the recently implemented Land Mobile Radio communication system used by military bases as part of the Homeland Security efforts. More + Product Details Close
Overhead Door® openers and garage doors are built with longevity in-mind. By performing a few routine tasks, you can help ensure your garage door system stays safe and stands the test of time. One important part of garage door system routine maintenance is to make sure the photo-eyes have not gone out of alignment. The photo-eyes are the infrared sensors which monitor whether the space at the bottom of your garage door is clear. When these sensors are not lined up properly they will keep your door from closing. Make sure to occasionally check your photo-eyes’ alignment to ensure they are correctly detecting obstructions to keep your garage door safe and operating properly.
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
We strive to deliver the most relevant products, services, and guidance to provide you with customized and flexible solutions to meet your specific requirements and budget. Choosing us means that you will not be disappointed. We provide round-the-clock reliable garage door repair, garage door service and support in Orange County, CA. Champion Garage Door Repair is, therefore, your household name when it comes to garage doors and garage door repair service.
Finally, one of the most important garage door innovations over the years in increased child safety features. Sensors can detect when a child or pet is crossing the threshold while the door is closing, prompting it to stop immediately. Furthermore, doors can also sense when something is being pressed by the door, causing it to stop before inflicting a brutal crushing injury.
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011.