My garage door broke on a Saturday night as I was getting ready to leave for a holiday party. Kelvin was here within 30 minutes. He reviewed everything with me that was happening with my door. He gave me the estimates of what was immediately needed to be done in order for my door to raise and then what I will need to have done very soon. I could see all the problems he pointed out to me and I decided to have everything done. He completed everything that night. I was very satisfied with Kelvin’s professionalism and the work he did. Thank you again.


Since their invention in the 1920s, electric garage door openers have come a long way. Garage door openers work by using a trolley connected to an arm that attaches to the top of the garage door and slides back and forth on a track, which opens and closes the garage door. When operating the motor, a chain or belt turns and pulls the trolley along the track. A good garage door opener will have a horsepower of 1/2 HP, 3/4 HP, or 1-1/4 HP. Garage door openers have the ability to open and close a limited number of times in power outage emergencies. Security is something else to consider when purchasing an opener. It's helpful to have sensors that will stop the operation of the garage door when a person, vehicle, or other obstacle is in the way.
The replacement springs in my case proved to be 0.2253 wire size, 2.0 inch (inside) diameter, and 24 inches long, in a pair of one left- and one right-hand winding. Actually, the old springs in these pictures were a slightly smaller size, but another similar door on this garage was better balanced by that size. Whoever installed the old springs didn't quite get the weight and size just right; it is not unusual to find a repair service installing a slightly off-balance spring size that happened to already be on the truck during the service call. My electric opener had no trouble handling the small imbalance. But since it is safer to reduce the electric operating force as much as possible through careful balancing, I chose the size that was working better on the other door. The Chamberlain brand electric openers (also sold by Sears) I have incorporate a plastic worm gear that tends to wear out after some years of use, requiring a disassembly and installation of a $20 repair kit; this wear is minimized by a properly balanced door.
The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
Follow the directions. Torsion springs require careful adjustment so be sure to read the manual for your particular door to properly set the spring tension. This is crucial to the safe and correct operation of the door. Most garage door repairs should not take more than a few hours for basic maintenance repairs, or half a day with a helper for the more complex spring work.

No matter your service need, our garage door specialists in Houston are ready to help. We provide routine maintenance of your garage doors and gates, repairing broken components, and installing new doors and gates. You can always depend on Garage Service Pros to deliver speedy yet effective service. With same day service and availability 24-hours for emergencies 7 days a week, you will always have someone on the other end of the line when you need us most. We take great pride and provide excellent customer service in the following locations.
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
To estimate the maximum physical force required to wind these springs, consider that they are balancing the weight of the door with a torque applied to a lift drum on each end of the torsion shaft. The lift drums have a 2-inch radius, which is the standard residential size, and corresponds conveniently to about a 1-foot circumference. If we pessimistically assume the 10-by-7-foot door has a weight of 350 pounds, this implies a torque of 350 pounds on a 2-inch radius, that is, 700 inch-pounds, or 58 foot-pounds. Each of the two springs should be exerting slightly less than half of the balancing torque, or 29 foot-pounds. Compare this to, say, the bolts in an automobile, which are typically torqued to values of about 50 foot-pounds, or tire lug nuts, which may be torqued to well over 100 foot-pounds.

Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Once you’ve decided it’s time to replace your garage door — whether the result of malfunctions or just seeking to modernize your home’s exteriors — you may be wondering how much a garage door replacement costs. While these numbers are often determined by several factors, including the materials and labor involved, on average, a garage door replacement can cost just over $1,000 but could range from about $300 to over $2,000.
Looking for something powerful but don’t want it to be too loud? This garage door opener from Chamberlain is a great option. Featuring an exclusive Motor Vibration Isolation System which eliminates vibration for reduced noise, this is a good choice especially you have an attached garage with rooms above the space. It also has MyQ enabled technology that allows you to monitor and control the opener via your smartphone with an extra purchase of the product. You can set the opener’s timer to close the door one, five or 10 minutes if you forget, and it has sensors to make sure it won’t close if something is in its path. It comes with a lifetime motor, lifetime belt, five-year parts, and one-year accessories warranty.
As your Kentucky and Ohio garage door repair company, we offer a team of experienced and knowledgeable technicians who move with urgency to diagnose your issues of any garage door repair or service They’ll discuss your options, and then execute the option you’ve selected for your home. When you need the best in garage door service, installation and repair, choose AE Door & Window.
Smartphone Control: Many newer garage door openers allow you to connect the device to your home's Wi-Fi network, according to RW Garage Doors. You then can open and close the door through a smartphone app. In fact, many of these apps will give you an alert on the smartphone when the garage door is open for a certain period. Some opener models even can connect to your existing Smart Home system, incorporating all your appliances on one system.
You can expect to pay between $130 and $350 for a garage door opener, with most models costing an average of $200. The most expensive openers usually include extra accessories and smartphone controls, though most openers can work with a smartphone if you buy a Wi-Fi adapter such as MyQ. The types of garage door openers in increasing order of average cost are as follows: chain, belt, screw and direct drive.
Here is what a winding cone looks like without the spring. The threads that grip the inside of the spring coils are ambidextrous, so you can use the same part on either right- or left-hand-wound springs. The cone size is specific for a certain inner diameter of springs, so if you have the wrong size, the cone will slip inside the spring (cone too small), or not fit (cone too big).
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.
"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "
We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality.
As you go through the designer and create the style of door you like best, the options you selected are saved automatically, so that you can easily submit it to us for a free price quote. Submitting this form does not obligate you in any way and your email address and personal information are kept in the strictest confidence. See our privacy policy to learn more. The price quote you receive is an estimate and is NOT A GUARANTEED PRICE. Precision will, at no additional charge come to your home and provide you with a firm price. We just need to do some measurements before we can guarantee a price. Get started now by choosing a collection above!
Before purchasing a roll-up door, measure the space between the top of the garage door opening and the ceiling or overhead framing. Standard tracks require headroom of about 14 inches. If you don’t have that, you can get low-headroom track, which costs about $100 more. There are also tracks specially made for garages with unusually high walls or cathedral ceilings.

While you may be able to increase efficiency by replacing the weather stripping at the bottom of an old garage door, the kind of insulation and energy efficient materials used in today’s new doors will make a drastic improvement on your garage’s energy efficiency. Just like the way a new garage door recoups its costs in increased home value, a new door will also quickly pay for itself in energy savings!
Versatile. That’s one way to describe our products. A total, one-stop solution that meets your every upward-acting-door need. Featuring premium materials, superior craftsmanship and innovative functions, our products continue to lead the industry, underscoring a legacy of quality, expertise and integrity.  This history ensures that you are making a good investment in your home with a quality product. In fact, according to the latest  Cost vs. Value Report by Remodeling Magazine, replacing a basic garage door with an upgraded one returned up to 85%​ on original cost on average – making it one of the top renovations in the study.
You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]


Looking for something powerful but don’t want it to be too loud? This garage door opener from Chamberlain is a great option. Featuring an exclusive Motor Vibration Isolation System which eliminates vibration for reduced noise, this is a good choice especially you have an attached garage with rooms above the space. It also has MyQ enabled technology that allows you to monitor and control the opener via your smartphone with an extra purchase of the product. You can set the opener’s timer to close the door one, five or 10 minutes if you forget, and it has sensors to make sure it won’t close if something is in its path. It comes with a lifetime motor, lifetime belt, five-year parts, and one-year accessories warranty.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.

Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
(The Wahl correction factor accounts for additional stress in the material due to shear forces, although these forces do not contribute to the spring's torque. These shear forces become significant in designs using a low spring index, which is to say, a relatively thick wire for the coil diameter. The correction factor is applied to scale up the stress S to better predict the fatigue lifetime of the spring.)
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
The classic telephone bait-and-switch: This time-honored swindle, also called "false advertising", can show up in the garage door business. Here's how this scam works: When you call and say you have a broken spring, and ask for a repair price, you are told over the phone that the price is X dollars, which typically might seem a little better than the competition. When the repairman shows up, after looking at your broken door, he will casually and matter-of-factly tell you it will cost 2X. If they told you over the phone that it would cost X, well, that was only for one spring, and he must (he must, mind you) install not just one, but two. He will act surprised if you object, as if you should have known that from what you were told over the phone. If you expected to really pay just X, it was your fault for misunderstanding because you don't know anything about how garage doors should be repaired. (You will feel intimidated at this, since you honestly don't know anything, else why would you have called a repairman? Intimidation is a powerful tool against customer resistance.) If your door used only one spring to start with, he will insist on converting yours to two, telling you it is safer the next time a spring breaks. If you originally had two springs, he will tell you that he must replace both springs, and you must therefore pay double what was quoted. While it is true that converting or replacing both springs is a good idea, the bait-and-switch pricing is not. The "bait" is the low price quoted to you over the phone, which they never intended to honor, and the "switch" is switching the price to something higher on a pretense. This method of selling is literally criminal (for example, see Florida Statutes 817.44, all states have similar laws), but a service business can usually avoid detection or prosecution because there are no printed advertisements or other tangible evidence, just one-on-one phone calls. If you find yourself in the middle of this trap, then the proper response is to dismiss the repairman without paying a nickel. Don't expect that you will be able to negotiate a fair price with someone who is using criminal business methods. Certainly don't expect that he will accept a lower price because you accuse him of false advertising. If you absolutely cannot wait for another service call, then you'll have to accept the fraud, in which case you should do so quietly. People that use these methods typically have ways to mentally justify their behavior to themselves as a reasonable business practice, and won't react well to your suggesting otherwise, even though they are in fact small-time criminals, not shrewd businessmen.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
A standard residential door raises 7.5 feet, but since the door goes horizontal this is equivalent to raising the whole door for half that distance, or about 3.75 feet. So if the door weighs, say, 150 lbs, then the energy supplied by the springs is 3.75 * 150, or about 563 foot-pounds. This is like throwing a 50-lb sack of cement up a 11-foot flight of stairs. Or catching a 50-lb sack of cement dropped from 11 feet up.
With over 30 years experience, Delaware Express Garage Doors, LLC, takes pride in providing the best service and making sure you are 100% satisfied with our work. We specialize in Garage Door and Opener installation and repair. From simple garage door openers to cell phone enabled devices, our technicians will get your doors working safely with fast reliable service.

Please Note: Prices, promotions, styles and availability may vary by store and online. Inventory is sold and received continuously throughout the day; therefore, the quantity shown may not be available when you get to the store. This inventory may include a store display unit. Online orders and products purchased in-store qualify for rebate redemption. Rebates are provided in the form of a Menards® Merchandise Credit Check valid towards purchases at any Menards® retail store. Not valid for purchases on MENARDS.COM®.
The torsion shaft with lift drums on the ends is above the door. The standard residential door shaft is a 1-inch outside diameter hollow steel tube. The inside diameters of the bearings, drums, and winding cones are sized to loosely fit that 1-inch diameter shaft. At the center is a bearing plate, on either side of which are the torsion springs, or in some cases just one larger spring. The spring pictured on the left in the photo is broken about 1/4 of the way in from its left end. The black shaft with dangling rope and door bracket is the track for the electric opener.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
We have everything needed and the expertise required to make accurate repairs for every variety of garage door. Whether you have a steel, wooden, or composite garage door, one of our team members will be happy to help you diagnose the problem and then apply an effective solution. Our repair services include repairs for springs, cables, rollers, tracks, sections, and more! Is your door noisy? We know the right way to fix it! Call us any timeyou need us to fix a problem.
Of course, the best garage door openers offer much more than weather protection. They are quick and convenient when leaving or returning home. They can secure what might otherwise be a weak point of home security. Some can even alert you at work if your garage doors aren't closed properly. The challenge you face is finding the right one – this isn’t a product you can simply try out and return until you find the best fit for your situation.
The one excuse that makes the most sense is, "if we sell springs to a do-it-yourselfer, and he gets hurt installing it, we could get sued." I can sympathize with someone who wants to sell only to the trade and not bother with the risk of a spurious product liability lawsuit from an ignorant member of the public. But the lawn-mower dealers have figured out how to manage that kind of exposure, so this is not an absolute barrier to retailing garage door parts to the public. It doesn't explain why torsion springs at retail are virtually non-existent.

Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.


When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
The Lifestyle garage door screen is a fully retractable garage screen door that works with your existing garage door. The Lifestyle features an industry first, fully retractable passage door for ease of entry and exit without having to retract the entire system. The Lifestyle garage screen is fully spring loaded, making opening and closing quick and easy.
Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.

At Kitsap Garage Door, our Clopay commercial garage door catalog is designed to facilitate efficient and long-lasting operations. We have several options appropriate for any commercial industry, from fire stations and restaurants to concessions stands or ticket sales. Explore our selection of commercial garage doors, specialty products and accessories including:
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.

Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
Additionally, the B970 includes encryption features that prevent others from hacking the system to gain entry to your garage. Expert reviewers like this garage door opener a lot. The Tool Spy says the Chamberlain B970 justifies its higher price point by delivering excellent build quality and anti-vibration features. Consumer Search and Garage How To also approve of this unit.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
The best garage door openers have a lifetime warranty on their motor and belt or chain. While it’s common for motors to come with lifetime warranties, belt and chain and parts warranties are often not that generous. However, it’s not uncommon for parts warranties to extend several years. Often the warranties are limited and subject to specific stipulations that vary and are detailed in the user manuals.
Irvine, CA | Foothill Ranch, CA | Lake Forest, CA | El Toro, CA | Laguna Hills, CA | Laguna Woods, CA | Rancho Santa Margarita, CA | Coto De Caza, CA | Mission Viejo, CA | Aliso Viejo, CA | Laguna | Niguel, CA | Laguna Beach, CA | San Juan Capistrano, CA | Dana Point, CA | Capistrano Beach, CA | San Clemente, CA | Corona Del Mar, CA | Ladera Ranch, CA | Cypress, CA | Dove Canyon, CA | Seal Beach, CA | Villa Park, CA | Westminister, CA | Anaheim, CA | Anaheim Hills, CA | Pomona, CA | Garden Grove, CA | Brea, CA | Placentia, CA | Fullerton, CA | La Palma, CA | Buena Park, CA | La Habra, CA | Costa mesa, CA | Cowan Heights, CA | Fountain Valley, CA | Huntington Beach, CA | Newport Beach, CA | Balboa Island, CA | Tustin, CA
If you live in a home where there are living quarters directly above the garage, Garage Guide DIY says force-sensing technology built into the B730 ensures a smooth operation, no matter what temperature it is in your garage. The unit adjusts the motor's power on the fly, keeping it running smoothly. Amazon reviewer Steven Bone says the B730/WD962KEV opener runs extremely quietly and is easy to install.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Finally, one of the most important garage door innovations over the years in increased child safety features. Sensors can detect when a child or pet is crossing the threshold while the door is closing, prompting it to stop immediately. Furthermore, doors can also sense when something is being pressed by the door, causing it to stop before inflicting a brutal crushing injury.
The most common grade of torsion springs have an expected life of about 10,000 cycles. The hardened and tempered steel experiences tremendous forces each time the door opens or closes. Gradually, the steel fatigues with each flexure, and eventually cracks and breaks, usually releasing its stored energy in an instant with a horrific "sproing" noise or bang. If you average about two car trips per day, opening and closing the door a total of 4 times daily when you come and go, then that expected life becomes 2500 days, or only about 7 years. If you have an automatic opener, then if you're like me, you tend to cycle the door even more frequently, and can expect the need for spring replacement even sooner. Moreover, my three-car garage has three doors, so on average I can expect a repair job every few years. Over a lifetime, it is very economical to do these repairs myself.

Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
This opener is easy to install for most DIYers and comes with two remotes and a wireless keypad so you can open the door with a pin. If you are interested in having this smart-enabled you can purchase a separate kit to do so. The Safe-T Beam helps prevent accidents using a infrared beam that will open or close the door if a car is getting to close. 
Customers who have purchased this garage door opener for their homes have been mostly satisfied with the performance of it. Many have raved about how quiet it actually is—one said instead of hearing the metal squeak and clank like with their last one, only the sound of the “wooden door being jostled around as it is pulled up and down” is all you hear with this one. Customers were also happy with the features including the automatic closer when you forget to shut it after you go inside. Some had had issues with the manual being hard to understand while installing it themselves. But most were happy with the overall performance.
Whether you're looking for the beautiful " Carriage House" style that adds beauty to your home, an energy efficient door that keeps your home warm or cool while reducing energy bills, or just needs a Custom Garage Door we've got a model that fits your needs. Learn more here.. Or come visit us at our new showroom to check out 25+ door models in person.
Our technicians are specially trained to handle a variety of garage brands, styles, and configurations. After arriving at your home, a Sears technician will diagnose the problem and walk you through the options for fixing it. Next, the technician will make any necessary adjustments or replace broken parts to ensure the door can be operational once again. We always attempt to complete repairs the same day of service, and your satisfaction is guaranteed. Our representatives are standing by for your call and are happy discuss pricing options.
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
Just compare our total price—item price + tax (if applicable) + shipping&handling—to the total price of other Online stores. If you find a lower price, we will match the price and refund 10% of the difference. Call us at 1-877-357-Door (3667) today with your quote from a competitor. We will review the lower price while processing your order and make any necessary reductions before your order ships.
×