You depend on your garage doors to provide safety and security at your home or office. They are also great for enhancing your property’s curb appeal and increasing its value. With their many moving parts and how they operate, you must have access to a reliable service company when something goes wrong. Houston residents and businesses trust us to make sure their garage doors will work when they need it to.

Garage Door Service Company


See the Sectional Overhead Garage Door catalog (PDF file) from the Prime-Line replacement hardware company. Their brochure Sectional Garage Door Torsion Spring Installation Instructions (PDF file, part number GD-12280) is brief but informative. Apparently you can only obtain their torsion springs as special order items through mom-and-pop type hardware stores like Ace and True Value, and not the big-box Home Depot and Lowes.
But the insulation won’t save energy unless you heat the garage or treat your attached garage as part of the “conditioned” part of your house. The federal Energy Star program recommends against doing this if you park cars, store lawn chemicals, or use solvents there because it could let dangerous fumes inside; it’s better to insulate only the shared wall and use that as the indoor-outdoor boundary.
Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Garage doors break on their own schedule which is why we offer 24/7 Same Day Garage Door Repair. Emergency Service is also available upon request 7 Days a week. Say Goodbye to return trips because our expert Technicians Service Major Brands and are Equipped with Fully Stocked Trucks. When the garage door breaks, J&S Overhead Garage Door Service is your local Garage Door Repair Specialist. Whether your garage door or opener is not working our expert technicians will repair or replace any garage door system on the spot. Proudly serving Hampton Roads including Virginia Beach, Newport News, Chesapeake, Hampton, Yorktown, Suffolk, Portsmouth, Poquoson, Norfolk, Gloucester, Smithfield, Franklin, and Williamsburg, Virginia.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
Our business believes in high quality, expedient service. We don’t want to keep you waiting for parts, so that’s why we have a huge inventory of springs, weather stripping, remotes, keypads, screens, and windows in stock for most units. No matter what part of your unit needs service, we’re sure to have a part that will fit. Our inventory doesn’t cover only a large variety of manufacturers, but is composed of only the highest quality components. By choosing the best, we’re able to offer a warranty on all of our repairs.
Even if one could somehow stretch and clamp the springs to the proper extra length, the process would still be more trouble, and there would be little or no reduction of risk. Lifting the full weight of the unsprung door by hand and clamping it in the raised position is dangerous in itself, and creates the same amount of stored energy as winding the springs, ready to slip out of your hands. Many doors won't travel far enough up the track to provide clearance to access the springs. You're also going to have to deal with winding stiff steel cables onto both lift drums at once without any resistance to maintain tension. Finally, even if you managed to complete the installation with the door raised, you then have to lower the massive door against an untested balancing torque. If you've made a mistake, then that massive door has nothing but your skeletal force applied through your meat clamps (hands) to prevent it from falling down and crushing whatever is in the way (perhaps your feet?).
As you go through the designer and create the style of door you like best, the options you selected are saved automatically, so that you can easily submit it to us for a free price quote. Submitting this form does not obligate you in any way and your email address and personal information are kept in the strictest confidence. See our privacy policy to learn more. The price quote you receive is an estimate and is NOT A GUARANTEED PRICE. Precision will, at no additional charge come to your home and provide you with a firm price. We just need to do some measurements before we can guarantee a price. Get started now by choosing a collection above!
Not sure what’s wrong with your garage door? Don’t know how much it will cost to repair? With Precision Garage Door Service of Lincoln, you’ll never have to worry about an unexpected bill. Contact one of our professionals today for a free technical evaluation and repair estimate. Once we’ve given you a price, you’ll be able to confidently make the decision whether you’ll want to move forward with the repair.
Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
Garage door frames and mouldings will freshen up the appearance of your garage and garage door. We offer frames in a broad assortment of finishes and widths, so you can find the perfect fit for your garage. Update or repair the hardware on your garage door with our wide selection of our garage door parts and accessories. Some of the accessories we offer include cables, hinges, reinforcement brackets, and locking door handles.
When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Disclosure: This post is brought to you by the Insider Picks team. We highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We operate independently from our advertising sales team. We welcome your feedback. Email us at [email protected]
Reduce your monthly energy bill with insulated garage doors. They feature an insulated core made of polystyrene that’s surrounded by a steel cover. This can help you maintain the temperature inside your home no matter if it’s extremely hot or cold outdoors. Insulated garage doors are also known for their quiet operation. Be sure to look at the insulation rating – or R-value – when considering garage doors. The higher the R-value, the better the insulation.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.

In 1993, U.S. law dictated that all garage doors must have a reverse mechanism to prevent the door closing on persons or property. In most models, an infrared beam running across the garage opening acts like a tripwire. Break the beam and the door rises again. This is a legal requirement that ensures the garage door cannot trap people or animals. It's also useful in avoiding accidental damage to your car, bikes left in the way, or other property.

Steel entry doors - when a garage is being fitted with new doors, it is also a good idea to consider a separate single 3x68 exterior door with half-glass and locksets too. These may require some carpentry, but they are a good way to allow for some flexibility in the choice of larger garage door, and can ensure that the homeowner will have more than a single way in or out of the structure. The average costs for such a feature range from $250 to $1000 each.
If the spring is broken near a winding cone, you might think you can remove and discard the short broken piece of spring from the cone, clean up the end of the long remaining spring, and insert that end into the cone. This is another extrememly risky improvisation. The shortened spring is not going to have the correct weight-bearing characteristics for the door, so you will not be able to balance the door properly. The shortened spring will be proportionately overwound, resulting in extra stress that will increase the expectation of another fracture. And the aging and history of the original spring being broken greatly increases the likelihood of another fracture at other locations.
Removing winding cones from an old broken spring for reuse in a new spring: Springs without the winding cones installed are a little cheaper than with the cones. Twisting the old cones into a new spring is easy with a vise and pipe wrench, but it can be tricky removing old cones from a broken spring for reuse. To remove old cones, mount the cone in a vise such that the spring portion is free. Grab the last few turns of the spring in a pipe wrench, engaging the teeth of the wrench into the end of the spring wire. Turn the wrench against the end of the spring wire, releasing the end of the spring from its clamping onto the cone, as you twist the loosened spring off the cone. Another more certain if not brutal method is to use an angle grinder with a thin metal-cutting disk to cut through the loops of spring wire where the loops wrap around the cones, being careful not to nick the cone itself too much. You could also cut into the old spring loops with a just hacksaw and break off the loops with hand tools, but this will require a lot of effort.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
Measurements: With the door in the down position, I measure a wire size of 0.273 inches, outside diameter of 2.0 inches, and overall length of 41.5 inches. Relaxing the spring shortens the length by about 7.5 coils of wire, so to estimate the relaxed length, we deduct the wire diamter of 0.273 inches times 7.5 from the 41.5 inch wound length, yielding an estimated relaxed length of 39.5 inches. The mean coil diameter is 2.0 - 0.273, or 1.73 inches. Perhaps this was actually a 40-inch-long spring with a 1.5 ID, 1.75 mean diameter, and 2.0 OD, but let's continue on calculating with the actually observed sizes. The number of coils in the relaxed spring is the relaxed length of 39.5 inches divided by the wire size of 0.273 inches, or about 145 coils. Deducting about 5 dead coils at the ends yields 140 active coils.
We are your trustworthy, affordable, and always accessible garage and gate service company. You enjoy quality service every time you choose Garage Service Pro. You can rely on our professional staff who are efficient and available every day of the week. We are a close-knit company that values loyalty and service. This is seen in our relationship with our customers as we truly care about delivering superior service no matter the job.
There are such a large number of varied issues with carport entryway repair. Stray pieces will be the dependable wind up being free with time. A bothering sound when you work the entryway opener is a marker that there is an isolated wandering part. Prior to an opening, it ensures that that the power supply is standing alone from the framework, or else you may hurt yourself. Now and again the gaps for stray pieces can expand the extent of to a degree that you can’t fix them. In such a case, you can employ wood fillers or perhaps regular wood pieces to top them off.
Add strength security and style to your home Add strength security and style to your home with a Clopay Garage Door. The 3-layer steel construction features polystyrene insulation for added energy efficiency and quiet operation. Decorative panel edging and natural embossed wood grain texture improve appearance close-up and from the curb. This door also features Clopay ultra-grain a ...  More + Product Details Close
As your Kentucky and Ohio garage door repair company, we offer a team of experienced and knowledgeable technicians who move with urgency to diagnose your issues of any garage door repair or service They’ll discuss your options, and then execute the option you’ve selected for your home. When you need the best in garage door service, installation and repair, choose AE Door & Window.
Trading wire size for length, diameter, or cycle life: Now we are really going to save you some money, if you just recall your high school algebra class (and I don't mean that cute cheerleader who sat next to you). If you further understand the role of the 4th power of the spring wire size (letter d in the formulas above) in the numerator of the spring rate formula, and how to increase or decrease d to compensate for changes in length, diameter, and cycle life, then you're qualified for elite spring calculations. Matching springs is a matter of equating the 4th power of the proportion in wire size change to the proportion of change in the diameter or length or the product of both diameter and length. However, it is usually best to only increase wire size when substituting a spring, since this does not derate the cycle life. If you observe that the formula for bending stress is proportionate to the inverse 3rd power of the diameter, then physically a proportionate increase in wire size will result in a dramatic increase in cycle life of the 3rd power of that proportion. Trade-off example: Yawn with me while we ponder my original spring once more. Let's say I was in a fit of engineering mania, and wanted to replace my spring having a 0.2253 inch diameter wire (d = 0.2253) with a 0.262 wire version (d = 0.262). How much longer is the spring with equal torque rate, assuming we use the same coil diameter? The proportion of this change is 0.262/0.2253 = 1.163, and the 4th power of that is 1.83. This means the length must increase by a factor of 1.83 (again, not counting dead coils). Recalling that the length in Example 1 was 102 non-dead coils, the heavier wire spring must be about 1.83*102 = 187 coils, which when adding 5 dead coils and multiplying by the wire size to get the overall length, is (187+5)*0.262 = 50 inches, versus 24 inches in the original. So using this heavier wire more than doubles the length (and thus the mass and thus the cost). While the cost about doubles, the stress goes down by the inverse 3rd power of the wire size proportion, or 1/(1.163**3) = 0.64. Sress is favorably, non-linearly related to cycle lifetime (halving the stress more than doubles the lifetime), so this decreased stress should more than double the expected lifetime of the spring. While the up-front cost is more, the true cost of an amortized lifetime is much less. In short, per cycle it is cheaper. Ah, the wonders of engineering calculations! Conclusion: Observe that the stress formula (and thus the cycle lifetime) depends only on wire diameter (d) for equal torques. Thus the only way to improve cycle lifetime is to use heavier wire. For equal torques, heavier wire size, due to the exponents in the formulas, increases cycle lifetime much faster than it increases mass (and thus cost), physically speaking.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.
If this manipulative, we-are-your-nanny business approach is truly in our best interests as consumers, then we shouldn't be allowed near ladders, lawn mowers, or power tools. Those products are just as hazardous and prone to misuse as torsion springs, yet no one thinks of them as forbidden. The only genuine difference is that torsion springs are a hazardous thing you need only rarely, while a lawn mower is a hazardous thing you need all the time.

Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
As you go through the designer and create the style of door you like best, the options you selected are saved automatically, so that you can easily submit it to us for a free price quote. Submitting this form does not obligate you in any way and your email address and personal information are kept in the strictest confidence. See our privacy policy to learn more. The price quote you receive is an estimate and is NOT A GUARANTEED PRICE. Precision will, at no additional charge come to your home and provide you with a firm price. We just need to do some measurements before we can guarantee a price. Get started now by choosing a collection above!
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
At Garage Doors & More, we are an authorized dealer for Pella, Amarr, Clopay and Haas Garage Doors. Feel free to check out our site to find the door that fits best for your home. In the top navigation bar there is a drop down. The garage doors tab is where you will find traditional garage doors. There is also another tab that will lead you to a page for our energy efficient garage doors. Other tabs include pages for our Carriage Garage Doors and Wood Garage Doors. You can also click the button below to see some of our special offers!
Appliance Repair Tulsa, OK 1600 Miller Trunk Hwy Appliance Repairs 1400 N Parham Rd Appliance Repairs Freehold Appliance Repair Kahului Maui Appliance Repair Appliance Repair in Clovis Eureka, CA Appliance Repair 2800 N Germantown Prkway Appliance Repairs 7700 E Kellogg Dr Appliance Repairs Appliance Store Melbourne Appliance Store Victoria Appliance Repair in Fort Worth Appliance Repair Puyallup, WA 10 W Lake St Appliance Repairs Appliance Repair in Arlington Appliance Repair in Frisco Saint George Appliance Repair Appliance Repair in Cedar Park Appliance Repair in Elizabethtown
Don’t miss out on all the modern conveniences and safety improvements that homeowners with automatic garage door openers enjoy. You deserve a garage door that you can open and close remotely. You deserve a garage door that doesn’t force you to get out into the rain and snow to operate it. You can have it with a simple phone call to A1 Garage Door Repair Madison. You can even choose form our fine selection of garage door opener products and have us install it for you.
Most importantly, you will be greeted by friendly staff and associates that will help you select the right garage door for your home. We welcome the opportunity to supply, install, and/or repair your garage door as well as answer any door questions you may have. When you choose us, you will quickly discover why thousands of Riverbend area customers from house to house and generation to generation have chosen Dan's Garage Door Service as their “DOOR KEEPER” for over 40 years.
We’ve been reviewing the best garage door openers for more than half a decade. This year we chose the Chamberlain Premium as our top pick. It’s an efficient, reliable garage door opener, and it comes with a backup battery system that works in a power outage. This model also has a preinstalled timer that closes your garage door automatically so you don't have to worry about whether you left the garage door open.
Your garage door is most likely the largest opening on your home, and as a result, it can affect your home’s energy efficiency. For homes in areas that experience colder winters or warmer summers, choosing an insulated door can save you money and improve the comfort of your home. Doors insulated with our Intellicore® insulation technology operate more quietly and are more durable. We also offer insulated glass window options that can help maintain energy efficiency and allow natural light into your garage. Visit our insulation guide to learn more about garage door insulation, or learn more about Intellicore® here.
×