Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.
Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door (Image 1). When ready, release the clamp and take the weight of the door.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
When you call on Precision Door, you can rest assured a talented professional will arrive at your home. Our technicians are professionally trained and field tested by the best in the industry at one of our two, state-of-the-art training facilities prior to servicing your door. Plus, successfully repairing over 1000 garage doors each day teaches you a lot. There is no substitute for experience
In my case, removing and replacing the relaxed springs required that I take down the assembly: torsion shaft, lift drums, and bearings. Doing that requires unbolting the center bearing plate from the wall, removing the drums from the shaft, and finally sliding the shaft back and forth out of the end bearings to remove the whole assembly off the wall. I am fortunate to have a lot of clearance in this garage to make the disassembly simpler. Tighter clearance to walls or ceiling would make disassembly a more difficult manipulation.
Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system including Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion setups on the spot.
You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
Since we're using an 18-inch (1.5 feet) winding lever to wind each spring up to 29 foot-pounds, we must apply a maximum tangential force to the end of the winding lever of about 20 pounds. Later we'll see that the actual weight of this rather dense door is 238 pounds, implying a maximum tangential force on the winding levers of only about 13 pounds!
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly.
My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
You depend on your garage doors to provide safety and security at your home or office. They are also great for enhancing your property’s curb appeal and increasing its value. With their many moving parts and how they operate, you must have access to a reliable service company when something goes wrong. Houston residents and businesses trust us to make sure their garage doors will work when they need it to.
With more than 43 years of experience, Kitsap Garage Door is the trusted source for garage door and opener installation for home and business owners throughout the Kitsap, WA, area. We can dependably and expertly handle all of your garage door installation, maintenance or repair needs, and we offer a large selection of the most trusted and top-rated garage door brands and accessories available today. We’re proud to exclusively install Clopay garage doors and LiftMaster garage door openers.
Save now on garage doors and get ready to transform the look of your home. Home design experts agree: replacing your garage door can instantly transform the look of your home, almost more than any other exterior improvement. Let us help you select the right garage door to enhance your home's style. Trust us, your home will never look so good from the curb with one of our state of the art Garage Doors.
Measurements: With the door in the down position, I measure a wire size of 0.273 inches, outside diameter of 2.0 inches, and overall length of 41.5 inches. Relaxing the spring shortens the length by about 7.5 coils of wire, so to estimate the relaxed length, we deduct the wire diamter of 0.273 inches times 7.5 from the 41.5 inch wound length, yielding an estimated relaxed length of 39.5 inches. The mean coil diameter is 2.0 - 0.273, or 1.73 inches. Perhaps this was actually a 40-inch-long spring with a 1.5 ID, 1.75 mean diameter, and 2.0 OD, but let's continue on calculating with the actually observed sizes. The number of coils in the relaxed spring is the relaxed length of 39.5 inches divided by the wire size of 0.273 inches, or about 145 coils. Deducting about 5 dead coils at the ends yields 140 active coils.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.