For more than 35 years, AE Door & Window has served the Cincinnati and Northern Kentucky areas with high-quality Clopay garage door products and exceptional services. We started as a small company operating out of a garage. In the decades since we first opened, we’ve grown into a regional provider that businesses and homeowners turn to when they need garage door products, services and repairs.
It works well. Setup was straightforward. I had a hiccup, but it was because I inadvertently pulled the disable lever/chord and thought I’d ruined the opener. Flipped the lever and it works perfectly from the app and existing wall button/remote. 2-3 second delay in showing open/close when you use the wall/remote. Beeping and flashing lights for 5 seconds before closing (for safety).
These springs weighed in at just over 9 pounds each, including the winding cones. They are covered with a light film of oil, and at this point the job starts to get messy. The manufacturer has painted them with a "225B24" part number, which no doubt indicates the 0.2253 inch wire size, 24 inches long. Perhaps the "B" indicates the 2-inch inside diameter. Both the left- and right-hand springs have this same number on them.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

The usually recommended rule for a door being properly balanced is that it should lift "easily" through all its travel. The door may also remain stationary if let go somewhere around the middle of the travel, but a smoothly rolling door many not show this behavior (while a sticky track will!), so easy travel is the only reliable test for proper balance. A difficult door may be due to stiff bearings or rollers in the mechanism, tracks out of alignment, etc., not necessarily the torsion spring adjustment.

Spring index lower limit: DASMA standard 102-2004 provides a lower limit of 6 for the spring index, which is symbol C in our formulas above (section 9.3). Other interesting items in this standard include an upper limit for how much the door sags when raised (no more than 1/120 of its width, section 9.2.1), that each of the two bottom brackets should sustain twice the door assembly's weight (section 9.2.2) for a total safety factor of about 4, and that the lift cables should provide a safety factor of 5.
Give your garage a great look with garage doors from Menards®. Menards® has all the supplies, tools, and accessories you need to install a stylish new garage door. Choose the perfect door from our selection of residential and commercial garage doors as well as roll-up doors for storage sheds. At Menards®, you will find a wide variety of door sizes ranging from 4 feet to 9 feet wide, 10 feet to 16 feet wide, and over 16 feet wide. Because of the layer of insulation, insulated garage doors are generally quieter than noninsulated doors. Insulated doors also offer improved energy efficiency, so you can stay comfortable while working in the garage no matter what the weather's like outside.

Your garage door is most likely the largest opening on your home, and as a result, it can affect your home’s energy efficiency. For homes in areas that experience colder winters or warmer summers, choosing an insulated door can save you money and improve the comfort of your home. Doors insulated with our Intellicore® insulation technology operate more quietly and are more durable. We also offer insulated glass window options that can help maintain energy efficiency and allow natural light into your garage. Visit our insulation guide to learn more about garage door insulation, or learn more about Intellicore® here.
See the Sectional Overhead Garage Door catalog (PDF file) from the Prime-Line replacement hardware company. Their brochure Sectional Garage Door Torsion Spring Installation Instructions (PDF file, part number GD-12280) is brief but informative. Apparently you can only obtain their torsion springs as special order items through mom-and-pop type hardware stores like Ace and True Value, and not the big-box Home Depot and Lowes.
Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.

Removing winding cones from an old broken spring for reuse in a new spring: Springs without the winding cones installed are a little cheaper than with the cones. Twisting the old cones into a new spring is easy with a vise and pipe wrench, but it can be tricky removing old cones from a broken spring for reuse. To remove old cones, mount the cone in a vise such that the spring portion is free. Grab the last few turns of the spring in a pipe wrench, engaging the teeth of the wrench into the end of the spring wire. Turn the wrench against the end of the spring wire, releasing the end of the spring from its clamping onto the cone, as you twist the loosened spring off the cone. Another more certain if not brutal method is to use an angle grinder with a thin metal-cutting disk to cut through the loops of spring wire where the loops wrap around the cones, being careful not to nick the cone itself too much. You could also cut into the old spring loops with a just hacksaw and break off the loops with hand tools, but this will require a lot of effort.

Great!  We specialize in all sorts of garage door repair work.  Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own.  Most garage door companies will quickly remind folks about this, and it’s true.  Their are some hazards to watch out for when working around these heavy and high tension doors.  We recommend you give an expert a call to address the issue in a safe and timely manner for you.
Some of the best garage door openers offer special features like a backup power source or a timer that automatically closes the door behind you at a predetermined time. While the door openers we reviewed vary in terms of power, noise and efficiency, they are all effective in the all-important task of letting you come and go with the simple push of a button. Here are the criteria we used to rank the top garage door openers:
While there might not be a huge price range when it comes to garage door openers—they are all quite an investment—there a few less expensive options to consider. Here’s a great budget option from Chamberlain. It has a motor that’s equivalent to ½ horsepower and chain drive system that is quick and easy to install. You can also connect it to the MQ technology (gateway sold separately) to use with your smartphone. The product comes with two three-button visor remote controls, a multi-function wall control, as well as a wireless keyless entry system. It comes with a 10-year motor, two-year parts, and one-year accessories warranty.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
Yet another professional wrote me to say that the red paint on certain components of these assemblies is an "industry standard" that signals, "Danger! Part under hazardous tension." Other items under tension like the bolts on the cable attachment plate on the door should therefore also be painted red. If so, then this is a new, ambiguous, unreliable, and little-publicized standard, because none of my old hardware shows it, red paint also means other things, and searching the Web does not readily turn up references to this practice.
Now 13 pounds of force must be respected when backed by many hundreds of foot-pounds of stored energy, waiting to be released. Holding this torque is equivalent to stalling a 3 horsepower DC motor. But holding and turning these handles does not require extraordinary human strength. Note that this maximum tangential force depends only on the weight of the door, and the radius of the drums, and is divided by the number of springs (some designs have only one longer spring, as mine did originally, instead of two shorter ones). Higher or lower lift distances imply more or less turns to wind the spring (and thus a different spring geometry), but not more force on each turn.
Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
Your garage door is used often, generally more than any other door on your home. Therefore, it’s important to make sure that it’s tough, dependable and weather resistant. Our doors are fully capable of meeting all these requirements and are specifically designed with our customers in mind. While durability is important, so is appearance and we offer many different styles and colors of garage doors to match your home or business.
The replacement springs in my case proved to be 0.2253 wire size, 2.0 inch (inside) diameter, and 24 inches long, in a pair of one left- and one right-hand winding. Actually, the old springs in these pictures were a slightly smaller size, but another similar door on this garage was better balanced by that size. Whoever installed the old springs didn't quite get the weight and size just right; it is not unusual to find a repair service installing a slightly off-balance spring size that happened to already be on the truck during the service call. My electric opener had no trouble handling the small imbalance. But since it is safer to reduce the electric operating force as much as possible through careful balancing, I chose the size that was working better on the other door. The Chamberlain brand electric openers (also sold by Sears) I have incorporate a plastic worm gear that tends to wear out after some years of use, requiring a disassembly and installation of a $20 repair kit; this wear is minimized by a properly balanced door.
While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.

Once the springs are torqued, the setscrews tightened, and the locking pliers and winding rods removed, do not play with turning the torsion bar using the winding rods. Doing so even momentarily can relieve the tension on the lift cables, which then easily slip off the drums. Replacing the cables on the drums can be difficult without repeating the entire spring unwinding-winding procedure again, and the cables can be damaged if tension is applied while they are off the drums.
Once the shaft, springs, and center bearing plate come down and lay on the floor, the old springs should be easy to get off and new ones slid on and assembled. Two bolts hold the center cones to the center bearing plate. The bearing on the center plate can be oiled while it is exposed from having the springs off. At this point it is a relief to be working with inert parts while standing on the floor rather than energized parts while up on the ladder. You might think it would save a little time to replace the spring with the shaft left up on the wall, but I found it was easier and safer to lower the works down to the garage floor first.
It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).

Belt driven garage door openers offer a prime level of noise reduction if you want a silent environment in the garage. While common chainlinks will rattle during use, the smooth performance of a belt dampens noise as the garage door slides up and down. Using a 3/4 motor, the Genie SilentMax 750 will easily tackle any typical garage door while keeping the environment quiet and comfortable while in use.
There are plenty of garage door accessories to make your garage safer. Sears carries replacement safety sensors that will detect anything in the way and keep it from shutting. If you have a small garage or it's full of gardening equipment, a laser parking assistant will help you find the perfect spot every time. You can set it so it hits the perfect spot on your dash as you pull in. You'll also be able to find new tracks to replace worn opener tracks.
You’ll never have a difficult time reaching us here at Absolute Overhead Door. You will speak to another person 24/7 – never an answering machine or computer – no matter if you call day or night. Our team will always be ready to answer any questions that you may have and get a plan and schedule underway to fix everything from a broken spring, garage door opener, to a broken garage door that needs complete and new installation. If you need us to replace broken springs, you or your teenage driver backed into the garage door, or in the market for a new door install or upgrade, we’ve got you covered! We provide garage door service from 8am to 6pm – with no extra charge for evenings and Saturday’s. Absolute Overhead Door Service also provides 24-hour Emergency Service with minimal charge. We are your garage door repair and broken spring experts! If you have an unknown issue with your garage door or an issue with your garage door opener, give us a call today for guaranteed same day service. 

Establish an alternate entry to your garage or update an existing one with our selection of garage entry doors. With an entry door, you will lose less heat or air when you enter your garage to work. Our variety of garage and outdoor organization materials will help you keep all the items in your garage neatly and efficiently organized while our floor coatings and utility flooring will help ensure your cement garage floors last longer than if they were left untreated.
×