You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2016, for the United States. This is the latest information headed into the new year and is a great guide for 2017. I've also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs.

By watching the chalk mark while winding, you can count the number of turns applied, and confirm the number later. My standard-size door (7 foot height) with 4-inch drums has a nominal wind of 7-1/4 or 7-1/2 turns, which leaves 1/4 or 1/2 turn at the top-of-travel to keep the lift cables under tension. After 7 turns on the first spring, I clamped down the set-screws, weighed the door again, and found a lift of about 100 pounds in reduced weight. As expected, this wasn't quite half of the full 238 pounds, nor would it leave any torsion at the top-of-travel, so I added an 8th turn. The door now weighed 122 pounds on one spring, which was ideal. After winding the other spring, the door lifted easily, with only a few pounds apparent weight. This confirmed that the spring choice was properly matched to the door design. I engaged the electric opener trolley, and adjusted the opener forces down to a safer level suitable for the new, improved balance. The door was now ready for return to service.

Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
Unmatched or mismatched spring pair: You may find that you have a pair of springs that are different sizes. This mismatch may be a normal application, since the total torque on the torsion shaft is simply the sum of the torque contribution of each spring (indeed, very large doors can be lifted with 4 or more springs along the torsion shaft). The sum of the torque rates determine the lift; and dividing the torque among multiple springs does not change this. Some repair shops even apply mismatched pairs deliberately, since a few stock sizes of springs can be combined to fit a wider range of door weights than only matched pairs. For example, a technician may carry springs in increments of 20 lbs of lift, and when using pairs this allows a 20 lb increment in possible choices instead of 40 lb increments. Or, one spring from a pair may have broken and been replaced with a spring of equal torque rate but different size than the original.
I obtained my parts, as described on this page, from American Garage Door Supply Inc. (http://www.americandoorsupply.com/) They may have raised their small-order prices or imposed a minimum order since I ordered from them in 2002 at the prices in my essay above. The Web site offers a free catalog by PDF download or mail. Springs in 2005 were priced at $2.25/lb.

Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.


When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.

At Kitsap Garage Door, our Clopay commercial garage door catalog is designed to facilitate efficient and long-lasting operations. We have several options appropriate for any commercial industry, from fire stations and restaurants to concessions stands or ticket sales. Explore our selection of commercial garage doors, specialty products and accessories including:

Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.
Spring rate and torque: In my spring replacement above, the wire size was d = 0.2253 inches, and the ID was 2 inches, giving a mean diameter D = 2.2253 inches. The number of coils is L/d = 24 inches / 0.2253 = 107, less about 5 dead coils on the winding cones, or 102 active coils. Thus the spring rate is K = (π*28.5*10^6 * (0.2253)^4) / (32 * 102 * 2.2253) = 31.8 in-lb/turn (IPPT). Winding 7.5 turns * 31.8 in-lb/turn yields a torque of 238 in-lbs per spring.
Single panel doors are constructed from one monolithic panel. From the closed position a single panel door swings up and overhead with a hinge on each side (known as jamb type hardware) to the fully open position. A disadvantage of monolithic panel doors is that the swing up arc of the door occurs partially outside the garage. This means a vehicle must stop and park several feet in front of the door to avoid being hit by the garage door when it is opened.
Screw - Screw-driven lift systems attach a long screw to the motor to move the garage door. These systems are powerful, fast, relatively quiet and require less maintenance than typical chain- or belt-driven systems. Genie and Overhead Door are two popular brands that make screw-driven systems. Based on our research of Genie’s line, you can expect to pay $244 on average for a screw-driven garage door opener.

Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.
There are such a large number of varied issues with carport entryway repair. Stray pieces will be the dependable wind up being free with time. A bothering sound when you work the entryway opener is a marker that there is an isolated wandering part. Prior to an opening, it ensures that that the power supply is standing alone from the framework, or else you may hurt yourself. Now and again the gaps for stray pieces can expand the extent of to a degree that you can’t fix them. In such a case, you can employ wood fillers or perhaps regular wood pieces to top them off.
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.

Cycle lifetime unchanged by diameter-versus-length tradeoffs: Since the material stress (and thus cycle lifetime) for equal torques varies only with d, and not D or N, trading coil diameter (D) for spring length (N) in this fashion has no effect on cycle lifetime. Long and skinny, versus shorter and fatter, they'll wear the same if they have the same wire size and diameter-length product. The game of life is all about wire size when it comes to springs (see below).
The right side of the photo shows the center bearing plate where the stationary cones attach with two bolts. Some doors may have only one spring rather than two equal ones as shown here (indeed, old marks on the shaft show that this door originally had one spring about twice as long on one side). Above the center bearing plate is the bracket and track from the electric opener.
Removing winding cones from an old broken spring for reuse in a new spring: Springs without the winding cones installed are a little cheaper than with the cones. Twisting the old cones into a new spring is easy with a vise and pipe wrench, but it can be tricky removing old cones from a broken spring for reuse. To remove old cones, mount the cone in a vise such that the spring portion is free. Grab the last few turns of the spring in a pipe wrench, engaging the teeth of the wrench into the end of the spring wire. Turn the wrench against the end of the spring wire, releasing the end of the spring from its clamping onto the cone, as you twist the loosened spring off the cone. Another more certain if not brutal method is to use an angle grinder with a thin metal-cutting disk to cut through the loops of spring wire where the loops wrap around the cones, being careful not to nick the cone itself too much. You could also cut into the old spring loops with a just hacksaw and break off the loops with hand tools, but this will require a lot of effort.
Note that I am measuring a spring that is fully relaxed because it is broken!. The length of the relaxed, unbroken spring is the specification of interest. It is harder to measure unbroken springs on an intact door because the springs should not fully unwind, even at the top-of-travel. If you can't be certain of the spring diameter from indications on the cones, then you have to go through an unwinding procedure to relax them fully for measurement, or perhaps reckon the size from measuring the somewhat smaller diameter at the nearly unwound condition when the door is at its top-of-travel (although one should not attempt to raise a door with a broken spring).
Replace your old garage door and give your home a new look. Make it a custom garage door down to the tiny details. It's easy, fun and you can put together as many as you like before you get the perfect style for your home. Try our online customized garage door selector tool, and you'll have the garage door of your dreams on its way to you in no time. Standard, yet dependable wood-look steel doors, grooved-panel steel doors and classic raised panel steel doors are some of your options. Boost your style with barn garage doors for a unique, old-time yet modern look. Choose from hundreds of garage styles including traditional, carriage house and contemporary. If you spend time in the garage, let some light in, get a garage door with windows. The garage doesn't have to be just for cars, use the space however you need it - a play room for the kids, a workshop for hobbies, a studio. Let fresh air in but keep the bugs out with a garage door screen.
×