The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.
Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.

The Certified Technician, Rey Lopez, was competent, professional, polite, and willing to work. He quickly removed the old door and installed the new one. He then explained the vast differences between what we originally had and what we'd just purchased (stronger spring/tension rates; increased viability of door opening/closing life; beefier hardware; plastic vs. nylon rollers; stronger door reinforcement). Ray performed with alacrity his tasks and then demonstrated the quiet, solid way the door retracted--no banging after the initial rise from the ground. Finally, his attention to detail was so precise that he enabled another remote controlling all three doors, plus he capped some frayed wires, thus solving the problem of why the door opened intermittently. I would rate him a "6" on a scale of "1-5", meaning he went above and beyond our expectations. His "can do" attitude, coupled with the deference he showed, will take him a long, long way. May HaShem richly bless him in his endeavors!read more
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!

You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.
We specialize in garage door Spring Replacements. Broken Garage Door Springs (Extension and Torsion) can be repaired on the spot. J&S Overhead Garage Door Service will replace your broken garage springs today. We use only the highest quality garage door parts available. Our Extension Springs and Torsion springs are designed to last longer than standard residential springs.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.
Spending your whole weekend setting up a new garage door opener is not on the top of most peoples list. This opener is easy to install for most levels of DIYers and it provides a quiet and reliable open and close. This has 3/4 HPc DC chain features and the powerhead can open 12" in a second. It has a wireless remote and Intellicode 2 security to prevent people from breaking into your home. 

If you have paired springs, you can take a shortcut here instead of using locking pliers. Simply apply a slight torsion to the bar by clamping one of the springs with an easy half-turn or so applied. This will hold the lift cables in slight tension while you wind the other spring. If you have a single spring design, you can't use this trick, and have to use the locking pliers.
Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
By watching the chalk mark while winding, you can count the number of turns applied, and confirm the number later. My standard-size door (7 foot height) with 4-inch drums has a nominal wind of 7-1/4 or 7-1/2 turns, which leaves 1/4 or 1/2 turn at the top-of-travel to keep the lift cables under tension. After 7 turns on the first spring, I clamped down the set-screws, weighed the door again, and found a lift of about 100 pounds in reduced weight. As expected, this wasn't quite half of the full 238 pounds, nor would it leave any torsion at the top-of-travel, so I added an 8th turn. The door now weighed 122 pounds on one spring, which was ideal. After winding the other spring, the door lifted easily, with only a few pounds apparent weight. This confirmed that the spring choice was properly matched to the door design. I engaged the electric opener trolley, and adjusted the opener forces down to a safer level suitable for the new, improved balance. The door was now ready for return to service.
We are your trustworthy, affordable, and always accessible garage and gate service company. You enjoy quality service every time you choose Garage Service Pro. You can rely on our professional staff who are efficient and available every day of the week. We are a close-knit company that values loyalty and service. This is seen in our relationship with our customers as we truly care about delivering superior service no matter the job.
Garage doors break on their own schedule which is why we offer 24/7 Same Day Garage Door Repair. Emergency Service is also available upon request 7 Days a week. Say Goodbye to return trips because our expert Technicians Service Major Brands and are Equipped with Fully Stocked Trucks. When the garage door breaks, J&S Overhead Garage Door Service is your local Garage Door Repair Specialist. Whether your garage door or opener is not working our expert technicians will repair or replace any garage door system on the spot. Proudly serving Hampton Roads including Virginia Beach, Newport News, Chesapeake, Hampton, Yorktown, Suffolk, Portsmouth, Poquoson, Norfolk, Gloucester, Smithfield, Franklin, and Williamsburg, Virginia.
If your door has two springs, most professionals and research online says that replacing both springs is the best option. Most torsion springs are rated for 10,000 close/open cycles. If only one of your springs is broken, both springs are still recommended to be replaced. Considering that your second spring will break soon anyways, this added on fix is only going to cost you about $50 extra to assure that you don't have to pay another service fee for a second visit.
Had a quick response to my call. thought I might have to wait a couple of days to coordinate their schedule and mine. To my surprise I received service in one and one half hours. Not only that but there was no sales call, technician Mike was fully prepared to give me a quote and complete the work as his vehicle carried everything needed. He very efficiently completed the work and cleaned up after I selected from the options. He replaced the springs all rollers and made needed adjustments expeditiously. I would recommend this firm to anyone needing garage door repairs.read more
The Heavy Duty Chain Extension Kit for 10 The Heavy Duty Chain Extension Kit for 10 ft. High Garage Doors is required for reliable everyday operation of Chamberlain heavy duty chain drive models in 10 ft. garage door applications. Featuring a quick-install extension rail and replacement chain the kit includes everything needed for quick and easy installation. Includes ...  More + Product Details Close
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 

However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.

Once the springs are relaxed and loose on the torsion shaft, the lift drums lose their tension on the lift cable, and the cable comes loose. The end of the cable is terminated by a press sleeve, which locks into a ramp on the drum. Different drum styles have a bolt or other method to fix the cable end to the drum. These steel cables are springy and won't stay in place without tension. If my pre-inspection had showed that these cables were worn or frayed, then I would have ordered proper replacements ahead of time from the spring distributor, since this is the opportunity to replace them. Standard hardware-store cable and fittings are not appropriate.
If you need quick Garage Door Repair In Los Angeles, Ca and the surrounding are , you have to search for Local Garage Door Repair, Inc within your region. Not simply would we be able to supply benefits instantly, we will positively do as such at a level rate. We will don’t charge crisis costs in the event that we advance crisis circumstance administrations, so make a point to consider this when picking our repair tech. At the point when you need your occupation fixed immediately, call Local Garage Door Repair, Inc techs to go to your home for repair administration necessities. Not just will we carry out the employment right, we will complete it for you instantly too.
We specialize in all varieties of garage door repair work. We have the tools and knowledge to get the job done safely. It can be somewhat dangerous to take on a garage door repair on your own, and most garage door companies will advise against attempting a DIY fix. There are some hazards to watch out for when working around these heavy and high tension doors. We recommend you give the experts at Girard's a call to address the issue in a safe and timely manner.

Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
We are a family owned and operated, local garage door company in the Carlisle area that believes in attention to detail and an emphasis on customer service and satisfaction. We even offer same-day service because we know that when your garage door isn’t working the way it should, you need it fixed fast. We offer affordable rates that will fit your budget, and we’re confident you won’t find another garage door installation company in Carlisle or the surrounding areas with the same dedication to our customers and the quality of our work at the affordable rates we offer our clients.
The prior clamping of the set-screws tends to have pressed a dimple into the hollow shaft and to have distorted the shaft's roundness into an eccentric shape. While releasing the set-screws, I was careful to loosen them enough to let the cone swing around any such distortions. I was also careful to observe any binding of the old cones on the eccentricity or burring on the shaft. The fit of the cone on the shaft is supposed to be loose enough to avoid binding, but if it were to occur one would have to be careful not to assume the spring was unwound when in fact the cone was just stuck on the shaft. If I had a stuck cone that I could not unwind with a little extra force, then I would have called in a technician to deal with it. In the worst case, I suppose the spring must be deliberately broken with some hazard, thus releasing it for a forceful disassembly, and the shaft and some other parts replaced. But this is an unlikely situation and in this case was not necessary.
Two of the spring references specifically for the garage-door industry are the APCO Spring Manual by Bill Eichenberger, and the Torsion Spring Rate Book by Clarence Veigel; these give tables of spring sizes and torque constants. Spring engineering principles in general are described in the Handbook of Spring Design published by the Spring Manufacturer's Institute; the formulas allow you to calculate torque constants knowing only the geometry and the Young's modulus of the material. You can also find some brief spring information in standard references like Machinery's Handbook and Marks' Standard Handbook for Mechanical Engineers.

The most common grade of torsion springs have an expected life of about 10,000 cycles. The hardened and tempered steel experiences tremendous forces each time the door opens or closes. Gradually, the steel fatigues with each flexure, and eventually cracks and breaks, usually releasing its stored energy in an instant with a horrific "sproing" noise or bang. If you average about two car trips per day, opening and closing the door a total of 4 times daily when you come and go, then that expected life becomes 2500 days, or only about 7 years. If you have an automatic opener, then if you're like me, you tend to cycle the door even more frequently, and can expect the need for spring replacement even sooner. Moreover, my three-car garage has three doors, so on average I can expect a repair job every few years. Over a lifetime, it is very economical to do these repairs myself.

The winding technique is simply to (un)wind as far as one rod will go, where it is pressed against the top of the door, or nearly so, by the unwinding torsion. You insert the other rod in the next socket, remove the first rod, and continue. At any point you can stop and rest by leaving the active rod pressed against the door, where it will be held by the unwinding force. I would make a quarter-turn increment that way, and let go for a moment to collect my attention for the next increment, almost in a quiet, meditative alertness. While you can go from one quarter-turn and rod-swap to the next continually without letting go, working fast against the steady tension seemed to invite a kind of shakiness in my arms that was a bit unsettling. It isn't that there is much physical exertion, it is more that the tension is unrelenting, like peering over a precipice.
You depend on your garage doors to provide safety and security at your home or office. They are also great for enhancing your property’s curb appeal and increasing its value. With their many moving parts and how they operate, you must have access to a reliable service company when something goes wrong. Houston residents and businesses trust us to make sure their garage doors will work when they need it to.
The third stage of garage door opener technology uses a frequency spectrum range between 300-400 MHz and rolling code (code hopping) technology to defeat code grabbers. In addition to transmitting a unique identifier for the remote control, a sequence number and an encrypted message are also sent. Although an intruder could still capture the code used to open a garage door, the sequence number immediately expires, so retransmitting the code later would not open the garage door. The encryption makes it extremely difficult for an intruder to forge a message with the next sequence number that would open the door. Some rolling code systems are more involved than others. Because there is a high probability that someone will push the remote's button while not in range and thus advance the sequence number, the receiver does not insist the sequence number increase by exactly one; it will accept a sequence number that falls within a narrow window or two successive sequence numbers in a much wider window. Rolling code technology is also used on car remote controls and with some internet protocols for secure sites.
You may not spend a lot of time thinking about your garage door, but dealing with a broken one can be a nightmare. If a door failure is keeping you from getting access to or storing your car, contact one of our trusted professionals for same day garage door repair in the Lincoln area. Our team is experienced in all areas of garage door repair including panel replacement, opener repair, carriage house servicing, leveling, speed adjustment, and commercial grade garage servicing. We service nearly every major brand and style of garage door. Whether you’ve got a vintage unit that needs a tune up or a modern keypad operated garage door that isn’t working the way you want, our experienced repair staff will be able to effectively address your needs.
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
If the spring is broken near a winding cone, you might think you can remove and discard the short broken piece of spring from the cone, clean up the end of the long remaining spring, and insert that end into the cone. This is another extrememly risky improvisation. The shortened spring is not going to have the correct weight-bearing characteristics for the door, so you will not be able to balance the door properly. The shortened spring will be proportionately overwound, resulting in extra stress that will increase the expectation of another fracture. And the aging and history of the original spring being broken greatly increases the likelihood of another fracture at other locations.
We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality.
There are plenty of garage door accessories to make your garage safer. Sears carries replacement safety sensors that will detect anything in the way and keep it from shutting. If you have a small garage or it's full of gardening equipment, a laser parking assistant will help you find the perfect spot every time. You can set it so it hits the perfect spot on your dash as you pull in. You'll also be able to find new tracks to replace worn opener tracks.
Once you’ve decided it’s time to replace your garage door — whether the result of malfunctions or just seeking to modernize your home’s exteriors — you may be wondering how much a garage door replacement costs. While these numbers are often determined by several factors, including the materials and labor involved, on average, a garage door replacement can cost just over $1,000 but could range from about $300 to over $2,000.
Beware of improprer prior installations: Sometimes the existing door installation is not correct, and the old springs should not be used as a specification for replacements. For example, the old springs might have been replaced with incorrect sizes because the last repairman didn't have the right one on his truck. If your door has never worked quite right, something like this might be the cause. To correct this, you must use the weight of the door to specify the spring, either from a spring rate manual giving spring torque constants, or from the formulas below.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.

Cable fail-safe redundancy: Based on the proper setting of the drums on the torsion shaft, the two lift cables divide the lifting force equally to keep the door level as it rises. This not only levels the door, but also provides a fail-safe mechanism. If one of the cables should fail, such as from breaking or losing its end attachment, the other cable will then carry the full weight of the door. This will pull the door up on one side with twice the normal force, while the other side falls from its now unsupported weight, tending to make the door bind in its tracks and jam. Although not foolproof, this is a safety feature of the design which keeps the door from falling catastrophically if a cable were to fail while the door was traveling. The jammed condition also prevents a lowered door from opening with the hazard of a single broken cable, further minimizing the chances of both cables failing. Since if one cable fails the other must sustain the full weight of the door, the cables and attachments are rated many times the normal working load of half the door weight. A proper safety inspection of the door should include a critical look at the cables and their attachments.


One can overwind the springs slightly, up to about 8 turns on a standard residential door (that is, 1/2 or 3/4 extra turns), to compensate for undersized or fatigued springs, or increased door weight from painting or humidity, but this results in more stress on the springs and therefore decreased lifetime. If the door is too heavy for that slight tweak, then different springs are needed.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.
Most importantly, you will be greeted by friendly staff and associates that will help you select the right garage door for your home. We welcome the opportunity to supply, install, and/or repair your garage door as well as answer any door questions you may have. When you choose us, you will quickly discover why thousands of Riverbend area customers from house to house and generation to generation have chosen Dan's Garage Door Service as their “DOOR KEEPER” for over 40 years.
Those who benefit from this anti-competitive behavior have many excuses for it. They claim that the product is too dangerous and infrequently needed for the public to purchase directly. They say the job is hazardous and requires techniques and tools with which the amateur will rarely practice, which is true. They write me in anger saying I don't understand how expensive it is to put a truck on the road with a technician and parts and salary and benefits and insurance and advertising and every other common business expense. They say it will take the homeowner hours of effort to do this safely and correctly, while they can do it in a fraction of that time and at a price that isn't worth the effort to save. But should they set themselves up as the judge of what you can and cannot do? Of what is an economical use of your time? Imposing minimum order quantities or charging retail prices for small orders is legitimate; inquiring into the purchaser's background is not.

Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path. [12][13]
The Chamberlain Whisper Drive takes control to a higher level than other models with its door and light automation features. The internal control panel has a sensor for motion-activated lighting. In addition, door closing can be instant or set automatically for 1, 5 or 10 minutes. We give this feature a top-notch rating because, should you forget to close your door, your garage will secure itself.
Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
×