The Lifestyle garage door screen is a fully retractable garage screen door that works with your existing garage door. The Lifestyle features an industry first, fully retractable passage door for ease of entry and exit without having to retract the entire system. The Lifestyle garage screen is fully spring loaded, making opening and closing quick and easy.
The special-price don't-tell-my-boss trick: In this scheme, after the technician has worked on your door for a bit, he will grimly notify you that he has discovered an additional repair needed, not just the spring(s). He will offer to do the work at a "special price" if you agree not to tell his boss. This air of conspiracy to get a bargain distracts and disarms you from critically thinking whether you really needed the repair in the first place (likely you don't), and whether the price is really a bargain (likely it isn't).
Trading diameter for length: Observe that in the spring rate formula in the table above, factors D (diameter of coils) and N (number of coils) appear together in the denominator of the spring rate formula. Algebraically, given equal wire sizes, this means that the product of the coil diameter and overall length produces the spring torque, not the diameter or length alone. Physically, this means that you can trade off torsion spring coil diameter versus overall length in inverse proportions to maintain the same torque rate. Trade-off example: A spring with 2-inch diameter coils that is 36 inches long equals a 1.5-inch diameter spring that is 48 inches long, because the product in both cases is 72 (inches squared). This assumes that wire size is equal in the trade-off, and that you have not counted dead coils in the length. Service technicians use this principle to make quick substitutions for what's on their truck versus what you need. But if you understand this, you're ahead of many technicians who don't know this trick. Maybe now you can educate the next one you hire.

Garage door openers make it easy to get your garage open without the struggle or the hassle of facing inclement weather. The latest garage door openers have new features such as timed close, battery backup and improved energy efficiency. Sears carries top-of-the-line garage openers that can run much more quietly and smoothly than old models. With a keypad feature, you'll be able to get into your house using a secure four-digit code. With a few new batteries in your remote, you'll be opening your garage with the push of a button.

Wood doors range from midprice to very expensive, depending on whether they consist of a lightweight wooden frame filled with foam insulation and wrapped in a plywood or hardboard skin (the least expensive) or are true frame-and-panel doors made of durable mahogany, redwood, or cedar. Wood doors usually carry a short warranty, perhaps only one year. 
We are your trustworthy, affordable, and always accessible garage and gate service company. You enjoy quality service every time you choose Garage Service Pro. You can rely on our professional staff who are efficient and available every day of the week. We are a close-knit company that values loyalty and service. This is seen in our relationship with our customers as we truly care about delivering superior service no matter the job.
Kevin gave 30 mins advance notice via text before arriving, and he was very friendly and knowledgeable about the Chamberlain garage door opener that we ordered on Amazon. I was pleased with the thorough model description provided, and customer reviews which helped with our decision making, and our package came on the same day that it was ordered! I liked the process of choosing 3 preferred appointment times, and receiving a confirmation email which included Kevin's picture. The install price was very reasonable, and I would gladly use your Home Service again!
In the United States, the Consumer Product Safety Improvement Act of 1990 required that automatic residential garage door operators manufactured on or after 1 January 1991 conform to the entrapment protection requirements of the 1988 version of ANSI/UL standard 325.[11] A requirement for redundant entrapment-prevention devices was added in 1993; such a system can use an electric eye, a door edge sensor, or any other device that provides equivalent protection by reversing the travel of the closing door if an object is detected in its path. [12][13]

Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.
Insist on having any old parts returned to you, and have that noted on the written order before work begins. An honest and competent technician will not object to this. The evidence will establish whether you really needed the parts or not, and you can consult another opinion if you have any doubts. This tends to deter the parts-upsell scam, and protects you even if you know nothing about what you're buying while under the pressure of making a costly decision. If the old parts mysteriously "disappear", then you have reason to be suspicious.
Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
Since the springs are winding "up" when the door is closing and going down, the fully closed position is the most stressful on the steel and thus the most likely position at the moment of failure. This is a good thing, because failure near the top-of-travel means that you suddenly have a large, increasing weight falling. Thus we see the principle that you should never be standing or walking under the door when it is opening or closing, especially if you do so manually instead of with an electric opener. When the springs are working correctly, the door appears nearly weightless, but this is an illusion that turns into a calamity when the springs suddenly fail.
You might not think it could get easier than pushing a big button to open a door, but some garage door openers make things even simpler by offering keyless entry and multiple remotes. Many models come with a keyless entry pad that mounts outside the garage door so you can gain access without a remote. While a remote is preferable for most situations, there are times when you need to get into the garage and don’t have it handy, so this is a nice feature to have.
Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.

Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
The two set-screws in the winding cones have a 3/8-inch square head, which fits a 3/8-inch open-end wrench or 8-point socket, or a 7/16-inch 12-point socket or 12-point closed-end wrench. I carried an extra wrench in my pocket while winding, since I didn't want to be holding a wound spring that I couldn't set because I had dropped the wrench (although one could rest the winding rod against the door in this case while picking up a dropped tool).
Location, climate and building codes are just a few factors to consider when determining which type of garage door is right for your home. Depending on the region you live in, you may need to choose a wind load option for your garage door. Wind loaded garage doors help safeguard your home in high wind prone areas. With garage doors serving as the largest and often times the primary entrance to the home, an insulated garage door may also be right for you.

Correct spring size is determined by factors such as the weight and height of the door. You cannot substitute a different spring and just tighten or loosen the winding to make it balance the load. Why? To maintain cable tension under all operating conditions, the spring must retain about one turn of unspent wind-up at the top-of-travel position, which with the lift drum size and door height predetermines the number of turns of winding at the bottom-of-travel; and furthermore the torsion of the fully-wound spring at the bottom-of-travel must be slightly less than that needed to lift the weight of the door when translated by the lift drums.

You must use springs that are matched to the weight of the door. You cannot compensate for the wrong size spring by adjusting the number of winding turns. If you do not know a proper spring size, then you or your spring supplier must calculate a proper size (see below) based on an accurate weight (within 5 pounds) of the door. So you must then in turn have an accurate weight.
It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, those also happen to be the kinds of days when cold and moisture combine to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is a minor icy connection between the two that can be broken when you hit the opener button.
Right-hand versus left-hand winding: Springs are chiral, that is, wound or "laid" in either a left- or right-hand orientation. This is a critical property of their design and specification; you cannot substitute a left for a right or vice versa. If you were to grasp the spring in your hand, and if your right hand orients the tips of your fingers like the ends of the coiled wire when your thumb points "out" of the core of the spring, then you have a right-hand spring; likewise left (which end you grasp does not matter). (This also happens to match the "right hand rule" of magnetic polarity, if you happen to be knowledgeable in such esoteric subjects.) Another way to identify the winding is to examine the spring vertically in front of you; if the coils facing you rise going to the right, it is right-hand (thus you can remember, "rise to the right is right-hand"), and likewise left indicates left-hand. Another way is to view the coil axially; a right-hand spring winds in a clockwise direction as it recedes away, and a left-hand spring counter-clockwise. Yet another way, not so easy to remember, is to hold the spring vertically and compare the coil shape to the letter "Z" (indicates right-hand lay) or the letter "S" (indicates left-hand lay).
In my case, removing and replacing the relaxed springs required that I take down the assembly: torsion shaft, lift drums, and bearings. Doing that requires unbolting the center bearing plate from the wall, removing the drums from the shaft, and finally sliding the shaft back and forth out of the end bearings to remove the whole assembly off the wall. I am fortunate to have a lot of clearance in this garage to make the disassembly simpler. Tighter clearance to walls or ceiling would make disassembly a more difficult manipulation.
We lead busy and sometimes hectic lives. It's easy for someone low on sleep and high on stress to accidently bump into their garage door leaving a little damage. If you're lucky it's just an individual garage door panel that's been damaged. This will leave you with the option of garage door panel replacment. There's a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you've got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you'll end up having to just replace the entire door. Many times it's actually easier and more cost effective to just replace the garage door.
Most situations allow you to replace spring(s) without removing the assembly from the wall, if there is enough clearance in the surrounding garage structure at the ends of shafts. By unbolting the end bearing plates and removing the drums, you can run the springs down to the ends of the shaft to remove and replace the springs. This avoids the balancing act of holding a long, wobbly, heavy shaft while climbing up and down a ladder. This is how the professionals get the job done in a few minutes.
Adding a new garage door provides a dramatic difference in your home’s appearance. When neighbors pass by, when guests pull up, or when you return from work, your house will have a distinct beauty that makes it a landmark of the neighborhood. The unique look you’ve always imagined — as well as the material, the finish, and the insulation can be found in our wide selection of garage doors.
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.

Cost was $88 for 2 pairs of springs, plus $21 shipping. (I had to order 2 pairs to meet the $50 minimum order.) They came with new cones inserted as shown at that price, so I didn't bother trying to remove and reuse the old cones to save a few dollars. The cones are quite difficult to remove from old springs and to insert in new ones, and the spring supplier will have the right tooling to do that easily. That was the best price I could find on the Web at the time, and didn't seem out of line with what parts like this might cost at at the building supply (if they only sold them). Contractors buy these much cheaper in quantities; they're just an ordinary high-carbon steel wire turned on a winding machine. I also found Web sites asking a lot more money, obviously trying to cash in on search-engine traffic from do-it-yourselfers. Others report that some local dealers sell springs at retail, but at a high price that eliminates any economy versus having them installed.
Beware of improprer prior installations: Sometimes the existing door installation is not correct, and the old springs should not be used as a specification for replacements. For example, the old springs might have been replaced with incorrect sizes because the last repairman didn't have the right one on his truck. If your door has never worked quite right, something like this might be the cause. To correct this, you must use the weight of the door to specify the spring, either from a spring rate manual giving spring torque constants, or from the formulas below.
The not-so-competitive advertising trick: How about this racket: We have all heard how you should get at least three bids for any home improvement jobs, right? In some areas the largest ads in the yellow pages are from a single business using various names and phone numbers, masquerading as independent competitors. When you call asking for prices, "they" all quote you very high numbers. You are tricked into thinking you have shopped around for the prevailing price. (The more modern version of this is multiple Web sites that all direct you to call the same person.) If you've ever had to call a plumber you may have unknowingly been a victim of a similar trick.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
Stress and lifetime: Calculating the maximal stress in the wire is useful for estimating the lifetime. Using the formula above, the bending stress S in the spring wire is 32*238/(π*0.2253^3) = 212 Kpsi. The spring index C is D/d = 2.23 / 0.225 = 9.88. The Wahl correction factor is Kw = (4C-1)/(4C-4) + 0.615/C = 1.15. The Wahl-corrected stress is Kw * S = 1.15 * 212 Kpsi = 244 Kpsi. This predicts about a 10,000-cycle lifetime, which is the standard "cheap spring" configuration originally installed. Note that while this stress is proportional to the torque being applied, it is also in proportion to the inverse third-power of the wire size. Thus slightly heavier wire sizes (and suitably adjusted D and/or L) radically improve the expected cycle lifetime of the spring.
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Next, the torsion shaft is reassembled with the new springs, the drums repositioned loosely on the shaft, this whole assembly slid back into the end bearings, and the drum set-screws tightened down. I tightened the set-screws about 1/2 or 3/4 of a turn after contact with the shaft, which provides a good grip, but does not distort the shaft. The drums can be set on their old positions, if they were correctly installed, which is snug up against the end bearings to remove any longitudinal play in the torsion shaft. Now the lift cable can be reattached to the drums, and a slight temporary torque applied to the shaft to keep the cable taut while the first spring is wound. This temporary torque is conveniently applied with a pair of locking pliers clamped on the shaft, positioned such that they hold the torque by pressing lightly against the wall above the door, before you start the spring winding, The locking pliers stay on the torsion shaft until you have finished the spring winding locked down the spring cone(s) with the setscrew(s), and removed the winding bars. Then you simply remove them with the release on the wrench handle. I feel that any job that doesn't require a trick manipulation with either locking pliers or duct tape (or in the ultimate case, both!) is just too boring. My trusty pliers look a trifle rusty ever since I used them to clamp something on my outdoor TV antenna "temporarily" and left them out in the weather for, oh, several years. The white stuff on the drum is paint overspray from the original painting of the garage interior.

Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.

If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
If you are replacing an old garage door, the first step is to measure your garage opening to ensure you are choosing a door with the correct dimensions. Even if you feel confident that your door is a standard size, measuring first can help ensure that buying your door is an enjoyable and smooth process. View our installation guide to get the needed measurements for your door. If you find that you have an odd-sized garage door, use our QuickDraw tool to see how a specific model will look in your desired size. If you have a unique vision for your home's curb appeal, Clopay can also design custom garage doors to meet your specifications.
×