If you're clever and equipped with a welder, you might think you could get away by welding a broken spring back together. At least two factors make this extremely risky. First, the weld itself may fail, either due to insufficient basic strength, or weakening of the nearby parts of the spring. Second, the fact that the spring was old and fatigued enough to break once, means that it is likely to break again soon at other location(s).
Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.

Garage Door Service Co


Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
Irvine, CA | Foothill Ranch, CA | Lake Forest, CA | El Toro, CA | Laguna Hills, CA | Laguna Woods, CA | Rancho Santa Margarita, CA | Coto De Caza, CA | Mission Viejo, CA | Aliso Viejo, CA | Laguna | Niguel, CA | Laguna Beach, CA | San Juan Capistrano, CA | Dana Point, CA | Capistrano Beach, CA | San Clemente, CA | Corona Del Mar, CA | Ladera Ranch, CA | Cypress, CA | Dove Canyon, CA | Seal Beach, CA | Villa Park, CA | Westminister, CA | Anaheim, CA | Anaheim Hills, CA | Pomona, CA | Garden Grove, CA | Brea, CA | Placentia, CA | Fullerton, CA | La Palma, CA | Buena Park, CA | La Habra, CA | Costa mesa, CA | Cowan Heights, CA | Fountain Valley, CA | Huntington Beach, CA | Newport Beach, CA | Balboa Island, CA | Tustin, CA
We guarantee same day garage door service on calls placed by 1:00 pm. We are on most jobs within 2 hours of the request for service being placed. All our technicians travel in fully stocked trucks to your home or business to enable us to complete nearly all overhead / garage door repairs on the first trip without the need for additional appointments just to complete the job. We guarantee to exceed the normal service appointment you have experienced with other garage door companies by implementing the Absolute 22-point inspection on all jobs that we take on. Our 22-point safety inspection ensures the customer that all vital mechanical and safety parts of the door are fully operational and functioning as they should be. This prevents any future service calls for our customer and in turn saves YOU, the customer, money!
The winding technique is simply to (un)wind as far as one rod will go, where it is pressed against the top of the door, or nearly so, by the unwinding torsion. You insert the other rod in the next socket, remove the first rod, and continue. At any point you can stop and rest by leaving the active rod pressed against the door, where it will be held by the unwinding force. I would make a quarter-turn increment that way, and let go for a moment to collect my attention for the next increment, almost in a quiet, meditative alertness. While you can go from one quarter-turn and rod-swap to the next continually without letting go, working fast against the steady tension seemed to invite a kind of shakiness in my arms that was a bit unsettling. It isn't that there is much physical exertion, it is more that the tension is unrelenting, like peering over a precipice.
As you go through the designer and create the style of door you like best, the options you selected are saved automatically, so that you can easily submit it to us for a free price quote. Submitting this form does not obligate you in any way and your email address and personal information are kept in the strictest confidence. See our privacy policy to learn more. The price quote you receive is an estimate and is NOT A GUARANTEED PRICE. Precision will, at no additional charge come to your home and provide you with a firm price. We just need to do some measurements before we can guarantee a price. Get started now by choosing a collection above!
Our value pick is the Chamberlain PD76EV. It costs about $50 less than our top pick, but it has most of the higher-priced model’s advantages. The PD76EV has the same lift capacity, horsepower, lift system and automation compatibility. However, it doesn’t come with advanced features such as a backup power source, close timer and keyless entry pad. If you can live without those, this opener is a great choice.
When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
The garage door is the gateway to your home. By choosing an Overhead Door™ residential garage door, you are doing more than making a home improvement investment. You are making us a part of your daily life and relying on us for safety, security and dependable operation. Indulge your sense of design with a garage door that sets your home apart with style, appearance, safety and comfort. With dozens of garage door models to choose from, the Overhead Door™ brand provides style and design options to fit every home. ​
The winding technique is simply to (un)wind as far as one rod will go, where it is pressed against the top of the door, or nearly so, by the unwinding torsion. You insert the other rod in the next socket, remove the first rod, and continue. At any point you can stop and rest by leaving the active rod pressed against the door, where it will be held by the unwinding force. I would make a quarter-turn increment that way, and let go for a moment to collect my attention for the next increment, almost in a quiet, meditative alertness. While you can go from one quarter-turn and rod-swap to the next continually without letting go, working fast against the steady tension seemed to invite a kind of shakiness in my arms that was a bit unsettling. It isn't that there is much physical exertion, it is more that the tension is unrelenting, like peering over a precipice.
Widths - in addition to doors coming in a range of styles, they can be found as double-width and single-width styles. There are some serious considerations when opting for one over the other. For example, if a homeowner decides to use a single door that covers the entire opening of a two-car garage they will have to make serious structural modifications to the entry way;
Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.
We would definitely recommend Precision to anyone that needs garage door services! We were able to get a service appointment right away! Tom arrived and was very professional and courteous. He took the time to go over what repairs were needed and provided an estimate. He was ready to do the repairs right then and there and within a few hours, we had our garage door up and running like new! Thanks to Tom and Precision for a positive experience!
The technician that came out, Todd Noel, was very friendly and professional. He fixed my problem quickly and did not overcharge me for something that I did not need. He also made some great recommendations for future work. Because of his level of service and my customer experience, I highly recommend Precision and will use them again in the future.

Resetting the drums, if needed: If the drums were incorrectly set in their old positions, one must reset both drums in new positions on the shaft. This is complicated by the presence of old dimples in the torsion shaft from previous setting(s), which must be avoided lest they improperly influence the new setting of the drums. To begin this process of resetting the drums, the door must first be lowered and resting level on the floor, the spring(s) must be in the unwound condition with their set-screws loosened, and the lift cables wrapped around the drums. If for some reason the door does not rest level on the floor, such as the floor being uneven, then insert temporary shims between the door bottom and the floor to bring the door up to level. Loosen the set-screws on the drums, and turn the torsion shaft to avoid the old dimples from the set-screws in the old drum position. Tighten the set-screw on the left drum (that is, on your left as you face the door from in the garage), creating a new dimple, and apply tension to its cable with the locking-pliers technique, enough tension to keep the cable taut but not enough to start to move the door up. Attach and wind the cable on the opposite (right) drum by hand until the cable is similarly taut, and set the screw, remembering that tightening the screw will tend to add a bit of extra tension to the cable. Both drums should now be fixed on the torsion shaft, with the cables about equally taut (listen to the sound when you pluck them like a guitar string) and the door still level on the ground. Setting the left drum first, and the right drum second, will allow you to take up any slack in the cable introduced by the left drum rotating slightly with respect to the torsion shaft as you tighten the set screws. This alignment and balance of the cables, drums, and door is critical to smooth operation and proper closing. If you have a single-spring assembly, the distance along the torsion tube from the spring cone to one drum is longer than to the other drum, which allows a bit more twist to one side than the other, and you may have to compensate with the setting of the drums.

Garage Door Service Co

×