A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."

Direct Garage Doors specializes in the supply of residential and commercial garage doors. If you're interested in purchasing a new garage door for your home or business or need to replace or repair your existing garage door, we can help! We can supply you directly from a range of the best residential and commercial products in a variety of styles and colors to enhance any residential or commercial property
The Insignia HomeKit garage door setup is cheaper in most instances than a similar setup from Chamberlain, which can range anywhere from $70 to $170 depending on what you need. Insignia’s offering launched quietly sometime this month and retails for $69.99, though it’s currently on sale for $44.99. If you want to get a general idea of the setup process, you can view the full manual right here.
Keep in mind that when the springs are released there is nothing to help with weight replacement. Garage doors weigh 150 pounds or more and if the door were not locked in place, there would need to be some way of holding it up until it can be lower manually. If no one is available to help, a clamp can be put on the track at the end of the door (Image 1). When ready, release the clamp and take the weight of the door.

Here are the winding rods inserted in the winding cone of the unbroken old spring, posed just for a picture. Note that I have carefully placed a sturdy, steady ladder just clear of the swing of the rods, such that when I am standing on the lower rungs to reach the rods, that my head and body are clear of the "kill zone" around the spring and cone. You must have a trustworthy platform to stand on, because a slip or shake of the ladder while you are winding can cause you to lose your socketed attachment to the cone, letting loose the spring. I would not trust an ordinary household step ladder for this purpose.
An extension spring counterbalance system consists of a pair of stretched springs running parallel to the horizontal tracks. The springs lift the door through a system of pulleys and counterbalance cables running from the bottom corner brackets through the pulleys. When the door is raised, the springs contract, thus lifting the door as the tension is released. Typically these springs are made of 11 gauge galvanized steel, and the lengths of these springs are based on the height of the garage door in question. Their lifting weight capacity can best be identified by the color that is painted on the ends of the springs.
The technician that came out, Todd Noel, was very friendly and professional. He fixed my problem quickly and did not overcharge me for something that I did not need. He also made some great recommendations for future work. Because of his level of service and my customer experience, I highly recommend Precision and will use them again in the future.
Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
The standard winding tools are simply a pair of 18-inch lengths of mild steel rod, 1/2-inch diameter. Winding cones can have different socket sizes (such as 5/8 inch instead of 1/2 inch), so it is important to measure the socket and select a matching rod diameter. Also beware that poor-quality cones may have a sloppy fit to the winding bars, and a loose fit presents a severe hazard of slipping at the worst moment; anything more than about an inch or two of play at the handle end is too loose for safety. I bought a 3-foot length of zinc-plated 1/2-inch diameter steel rod from Home Depot for about $3, which conveniently cuts into two halves of just the right length (the store might even cut it for you if you ask). A steel supplier selling at commodity prices might charge about 50 cents or so for such a piece that weighs about 2 lbs. Drill rod would work if used in the annealed condition in which it is originally sold, but the added expense provides no benefit and the brittleness (if it had been hardened and not annealed) would worry me a bit. Rebar, threaded rod, screwdrivers, etc., are absolutely foolish as they will not fit the socket snugly. Aluminum rod is definitely too weak, and will bend under the torque that must be applied. Longer rods would make for more leverage but unwieldly swing; shorter rods make for uncontrollable swing. As we'll calculate below, the 18-inch standard tool length is an appropriate compromise. Note that you do not need 18 inches of ceiling clearance above the torsion shaft to use an 18-inch rod, since you need not swing the rods above horizontal when winding.
Tools in Action says the Ryobi Ultra Quiet has plenty of versatility, as you can plug devices into the opener hardware, like a Bluetooth speaker, a fan, or even an 18V Ryobi cordless tool battery. When the opener has power, it will charge the battery. But if your home ever loses power, the 18V battery works as a backup to the garage door opener, allowing it to operate normally.
If you've researched this subject at all, you will no doubt have heard that you shouldn't be attempting torsion spring replacement as a do-it-yourselfer. That is generally good advice, so if you have any doubts about your abilities to do risky physical work on your own, hire the job out like everyone else. I found I was capable of doing this work with acceptable risk, because I intelligently understood the techniques, paid careful attention to methods and safety, knew how to use common tools in good condition, properly improvised the special tools I didn't have, and diligently attended to correctly performing a few moments of hazardous manipulation. I learned to do it purely on my own based mostly on bits of advice reluctantly given in Internet forums such as the Usenet newsgroup alt.home.repair. When I first wrote this page in 2002, there was no other do-it-yourself information available on the Web, and it was not until 2005 that reliable information disclosing the techniques started to appear elsewhere (see links below).
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.

Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
The disaster-is-nigh technique: As he inspects your door, the serviceman grimly calls your attention to "cracks" in your garage door. These appear very faintly in the middle of the door where the panels bow under their own weight when the door is up. This is normal, but the type of thing you wouldn't casually observe yourself. This surprising revelation disarms you, and you may find yourself strangely susceptible to the pitch for an entire new door.
Many garage door opener remote controls use fixed-code encoding which use DIP switches or soldering to do the address pins coding process, and they usually use pt2262/pt2272 or compatible ICs. For these fixed-code garage door opener remotes, one can easily clone the existing remote using a self-learning remote control duplicator (copy remote) which can make a copy of the remote using face-to-face copying.

"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "

​We know that your commercial ​door can take a beating. That's why we build quality, tough commercial doors to withstand the daily wear and tear of owning and operating a business. Engineered for excellence and backed by a dedicated nationwide network of Red Ribbon Distributors, Overhead Door™ commercial and industrial doors are the premier choice for durability, serviceability and hassle-free performance. ​​​​
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
The Entire job from order through installation was great. The person at Home Depot who helped us made sure we knew exactly what was needed and went over options answering all questions my Fiance had before I could. On install day the installers were not only on time but early which was perfect as i planned my day around them being there and it allowed me to leave a little earlier when they finished to take care of other things. They were polite, knowledgeable, and engaging. Read less

In the photo, you can see an extra lag screw on the bottom of the plate, reinforcing weak anchoring from the original two screws (hidden behind the springs). This extra screw was applied by a professional garage door technician on a previous repair visit. I have since replaced the backing with a sound plywood panel anchored into the concrete door header. Since these bolts clamp all the opposing torsion to the wall, the attachment must be sturdy.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
Whether you’re looking for garage door opener maintenance, garage door opener repair, or a brand new garage door opener, Sears Home Services can help. We’re your best, most-trusted option for fast, quick, and easy local service, repair, and maintenance of your automatic garage door opener. Whether your garage door won’t open or close, your garage door opener chain is broken, your automatic garage door opener won’t work after a power outage, your garage door won’t work when it’s cold, or your automatic garage door opener won’t stop running, we’ll connect you to the best local automatic garage door opener repair service technicians in the business. Technicians that are highly trained, licensed, vetted, nearby, and guaranteed to help fix all of your garage door opener needs. We have thousands of local technicians that are always “near me,” that can help you no matter what your appliance emergency.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

The not-so-competitive advertising trick: How about this racket: We have all heard how you should get at least three bids for any home improvement jobs, right? In some areas the largest ads in the yellow pages are from a single business using various names and phone numbers, masquerading as independent competitors. When you call asking for prices, "they" all quote you very high numbers. You are tricked into thinking you have shopped around for the prevailing price. (The more modern version of this is multiple Web sites that all direct you to call the same person.) If you've ever had to call a plumber you may have unknowingly been a victim of a similar trick.

To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.

This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
The garage door opener traditionally has been a simple device. And it still is for the most part. But as with a lot of household items, technological advances are finding their way into garage door opener hardware. There are quite a few cool features in modern garage door openers, some of which are things you never knew you needed to automate the process of opening and closing a garage door.
With the rods and other tools at hand, I am ready to begin. The first task is to remove the broken spring and its unbroken mate from the torsion shaft. To remove and disassemble the shaft and lift drums, the torsion on the unbroken spring must first be released. I used a ratcheting box-end wrench to loosen the set-screws while pushing the rod against the force I knew would be released when the screws let go. Later I switched to an open-end wrench for the set-screws, since some of the square screw heads were too rough to fit in the box-end wrench.
Today's garage doors come with those door sensors, and if anything is in the path of the door the sensor detects it and raises the door back to the open position. These precautions are important for families with young children or pets. Even if you don't have a mini me or furry friend running around your yard, it's a good idea to have a garage door that is safe for you, your guests and your belongings. 

"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "
It’s important to pick a door that suits the style of your house. If you live in a Craftsman bungalow, for example, you might want something that looks like the swing-out doors found on garages behind early Craftsman houses. Manufacturers of modern roll-up doors make them in styles that mimic the old swing doors, complete with faux strap hinges on the sides and a pair of handles flanking a deep groove in the center. 
Since the springs are winding "up" when the door is closing and going down, the fully closed position is the most stressful on the steel and thus the most likely position at the moment of failure. This is a good thing, because failure near the top-of-travel means that you suddenly have a large, increasing weight falling. Thus we see the principle that you should never be standing or walking under the door when it is opening or closing, especially if you do so manually instead of with an electric opener. When the springs are working correctly, the door appears nearly weightless, but this is an illusion that turns into a calamity when the springs suddenly fail.
Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.
These are just my observations as a consumer; I am not on a crusade to change the garage door industry. But I will observe that the Web is the innovation that can finally give intelligent consumers the advantage in these commercial games. Trade restraints work only when all sellers in the market collude in and agree to the scheme. If anyone, anywhere is selling freely, then the Web can help you find them. In the years since I have first published this information, a number of reputable Web-based merchants have appeared to supply the parts you need to repair your garage door as a do-it-yourselfer (and I have linked many of them below).

Appliance Repair Tulsa, OK 1600 Miller Trunk Hwy Appliance Repairs 1400 N Parham Rd Appliance Repairs Freehold Appliance Repair Kahului Maui Appliance Repair Appliance Repair in Clovis Eureka, CA Appliance Repair 2800 N Germantown Prkway Appliance Repairs 7700 E Kellogg Dr Appliance Repairs Appliance Store Melbourne Appliance Store Victoria Appliance Repair in Fort Worth Appliance Repair Puyallup, WA 10 W Lake St Appliance Repairs Appliance Repair in Arlington Appliance Repair in Frisco Saint George Appliance Repair Appliance Repair in Cedar Park Appliance Repair in Elizabethtown
In Maryland, wildfires are not common. However, thunderstorms are, and they often take out the power. Do not get stuck when power outages occur again. Consider a battery backup. If you are interested in finding out more about it, simply give us a call. Want to know which openers have them? Please take a look at these Precision-preferred garage door openers.

Follow the directions. Torsion springs require careful adjustment so be sure to read the manual for your particular door to properly set the spring tension. This is crucial to the safe and correct operation of the door. Most garage door repairs should not take more than a few hours for basic maintenance repairs, or half a day with a helper for the more complex spring work.
Spending your whole weekend setting up a new garage door opener is not on the top of most peoples list. This opener is easy to install for most levels of DIYers and it provides a quiet and reliable open and close. This has 3/4 HPc DC chain features and the powerhead can open 12" in a second. It has a wireless remote and Intellicode 2 security to prevent people from breaking into your home. 
Trading wire size for length, diameter, or cycle life: Now we are really going to save you some money, if you just recall your high school algebra class (and I don't mean that cute cheerleader who sat next to you). If you further understand the role of the 4th power of the spring wire size (letter d in the formulas above) in the numerator of the spring rate formula, and how to increase or decrease d to compensate for changes in length, diameter, and cycle life, then you're qualified for elite spring calculations. Matching springs is a matter of equating the 4th power of the proportion in wire size change to the proportion of change in the diameter or length or the product of both diameter and length. However, it is usually best to only increase wire size when substituting a spring, since this does not derate the cycle life. If you observe that the formula for bending stress is proportionate to the inverse 3rd power of the diameter, then physically a proportionate increase in wire size will result in a dramatic increase in cycle life of the 3rd power of that proportion. Trade-off example: Yawn with me while we ponder my original spring once more. Let's say I was in a fit of engineering mania, and wanted to replace my spring having a 0.2253 inch diameter wire (d = 0.2253) with a 0.262 wire version (d = 0.262). How much longer is the spring with equal torque rate, assuming we use the same coil diameter? The proportion of this change is 0.262/0.2253 = 1.163, and the 4th power of that is 1.83. This means the length must increase by a factor of 1.83 (again, not counting dead coils). Recalling that the length in Example 1 was 102 non-dead coils, the heavier wire spring must be about 1.83*102 = 187 coils, which when adding 5 dead coils and multiplying by the wire size to get the overall length, is (187+5)*0.262 = 50 inches, versus 24 inches in the original. So using this heavier wire more than doubles the length (and thus the mass and thus the cost). While the cost about doubles, the stress goes down by the inverse 3rd power of the wire size proportion, or 1/(1.163**3) = 0.64. Sress is favorably, non-linearly related to cycle lifetime (halving the stress more than doubles the lifetime), so this decreased stress should more than double the expected lifetime of the spring. While the up-front cost is more, the true cost of an amortized lifetime is much less. In short, per cycle it is cheaper. Ah, the wonders of engineering calculations! Conclusion: Observe that the stress formula (and thus the cycle lifetime) depends only on wire diameter (d) for equal torques. Thus the only way to improve cycle lifetime is to use heavier wire. For equal torques, heavier wire size, due to the exponents in the formulas, increases cycle lifetime much faster than it increases mass (and thus cost), physically speaking.
Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
Replace your old garage door and give your home a new look. Make it a custom garage door down to the tiny details. It's easy, fun and you can put together as many as you like before you get the perfect style for your home. Try our online customized garage door selector tool, and you'll have the garage door of your dreams on its way to you in no time. Standard, yet dependable wood-look steel doors, grooved-panel steel doors and classic raised panel steel doors are some of your options. Boost your style with barn garage doors for a unique, old-time yet modern look. Choose from hundreds of garage styles including traditional, carriage house and contemporary. If you spend time in the garage, let some light in, get a garage door with windows. The garage doesn't have to be just for cars, use the space however you need it - a play room for the kids, a workshop for hobbies, a studio. Let fresh air in but keep the bugs out with a garage door screen. 
×