Recently another type of opener, known as the jackshaft opener, has become more popular. This style of opener was used frequently on commercial doors but in recent years has been adapted for residential use. This style of opener consists of a motor that attaches to the side of the torsion rod and moves the door up and down by simply spinning the rod. These openers need a few extra components to function safely for residential use. These include a cable tension monitor, to detect when a cable is broken, and a separate locking mechanism to lock the door when it is fully closed. These have the advantage that they free up ceiling space that an ordinary opener and rail would occupy. These also have the disadvantage that the door must have a torsion rod to attach the motor to.
To estimate the maximum physical force required to wind these springs, consider that they are balancing the weight of the door with a torque applied to a lift drum on each end of the torsion shaft. The lift drums have a 2-inch radius, which is the standard residential size, and corresponds conveniently to about a 1-foot circumference. If we pessimistically assume the 10-by-7-foot door has a weight of 350 pounds, this implies a torque of 350 pounds on a 2-inch radius, that is, 700 inch-pounds, or 58 foot-pounds. Each of the two springs should be exerting slightly less than half of the balancing torque, or 29 foot-pounds. Compare this to, say, the bolts in an automobile, which are typically torqued to values of about 50 foot-pounds, or tire lug nuts, which may be torqued to well over 100 foot-pounds.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.
Welcome to Jarusewski’s Overhead Door Service Inc. We are a locally owned company that has been providing the Carlisle, PA area with garage door sales and service since 1988. We specialize in installation, repair and maintenance of residential and commercial garage doors. Our garage doors are reliable, affordable and most importantly safe.We know a great garage door installation is nothing unless you have a great garage door to install. That’s why we feature the best brands when it comes to garage doors and garage door openers. We feature doors by Clopay, as well as, door openers by Chamberlain and LiftMaster Professional.
The second stage of the wireless garage door opener system solved the opening-the-neighbor's-garage-door problem. The remote controls on these systems transmitted a digital code, and the receiver in the garage responded only to that code. The codes were typically set by eight to twelve DIP switches on the receiver and transmitter, so they allowed for 28 = 256 to 212 = 4,096 different codes. As long as neighbors used different codes, they would not open each other's garage doors. The intent of these systems was to avoid interference with nearby garage doors; the systems were not designed with security in mind. Intruders were able to defeat the security of these systems and gain entry to the garage and the house. The number of codes was small enough that even an unsophisticated intruder with a compatible remote control transmitter could just start transmitting all possible codes until he found one that opened the door. More sophisticated intruders could acquire a black box master key that automatically transmitted every possible code in a short time. An even more sophisticated method is known as a replay attack. The attacker would use a code grabber, which has a receiver that captures the remote's digital code and can retransmit that digital code at a later time. The attacker with a code grabber would wait nearby for the homeowner to use his remote, capture the code, and then replay the code to open the door when the homeowner was gone. Multicode openers became unpopular in areas where security was important, but due to their ease of programming, such openers are often used to operate such things as the gates in gated apartment complexes.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
If this manipulative, we-are-your-nanny business approach is truly in our best interests as consumers, then we shouldn't be allowed near ladders, lawn mowers, or power tools. Those products are just as hazardous and prone to misuse as torsion springs, yet no one thinks of them as forbidden. The only genuine difference is that torsion springs are a hazardous thing you need only rarely, while a lawn mower is a hazardous thing you need all the time.
However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
The "safety issue" trick: Another tip-off is the use of language like "safety issue". This is meant to trump any objections you might have to a costly repair bill. Don't be manipulated by the suggestion that you are risking disaster if you don't buy something expensive. Even if you think the risk is genuine, get another estimate, and tell the second repairman you are skeptical; every technician loves to prove the competition made a mistake.
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.
The classic telephone bait-and-switch: This time-honored swindle, also called "false advertising", can show up in the garage door business. Here's how this scam works: When you call and say you have a broken spring, and ask for a repair price, you are told over the phone that the price is X dollars, which typically might seem a little better than the competition. When the repairman shows up, after looking at your broken door, he will casually and matter-of-factly tell you it will cost 2X. If they told you over the phone that it would cost X, well, that was only for one spring, and he must (he must, mind you) install not just one, but two. He will act surprised if you object, as if you should have known that from what you were told over the phone. If you expected to really pay just X, it was your fault for misunderstanding because you don't know anything about how garage doors should be repaired. (You will feel intimidated at this, since you honestly don't know anything, else why would you have called a repairman? Intimidation is a powerful tool against customer resistance.) If your door used only one spring to start with, he will insist on converting yours to two, telling you it is safer the next time a spring breaks. If you originally had two springs, he will tell you that he must replace both springs, and you must therefore pay double what was quoted. While it is true that converting or replacing both springs is a good idea, the bait-and-switch pricing is not. The "bait" is the low price quoted to you over the phone, which they never intended to honor, and the "switch" is switching the price to something higher on a pretense. This method of selling is literally criminal (for example, see Florida Statutes 817.44, all states have similar laws), but a service business can usually avoid detection or prosecution because there are no printed advertisements or other tangible evidence, just one-on-one phone calls. If you find yourself in the middle of this trap, then the proper response is to dismiss the repairman without paying a nickel. Don't expect that you will be able to negotiate a fair price with someone who is using criminal business methods. Certainly don't expect that he will accept a lower price because you accuse him of false advertising. If you absolutely cannot wait for another service call, then you'll have to accept the fraud, in which case you should do so quietly. People that use these methods typically have ways to mentally justify their behavior to themselves as a reasonable business practice, and won't react well to your suggesting otherwise, even though they are in fact small-time criminals, not shrewd businessmen.
A basic low cost garage door is made of steel reinforced with cross members. It is light and durable. Steel doors have a wood grain finish so that they look very nice. Wood doors are not installed as often as in the past, but they are still available. For those for whom budget considerations are secondary to appearance and value, there are many, many types of doors. Decorative garage doors can make a big difference in the appearance of a home, raising the home's value by as much as 4%. When you're ready to discuss your garage door design options, just call us.
Checking if the lift drums need resetting: The old position of the lift drums on the shaft may have slipped or otherwise lost the the proper position, requiring a reset of the drum position on the torsion shaft. You will also reset the drums if you are replacing the lift cables, since the new cables will not exactly match the length of the old ones. Problems like uneven tension on the cables, or a tilted door, or a door that doesn't easily stay aligned with the tracks, can be due to an improper "set" of the drums on the shaft. So one shouldn't assume the old positions are correct. Setting the drums on a "fresh" part of the shaft will avoid the possibility of damaging the shaft from retightening in the same dimples.
This is the electric opener which operates this door. I'm picturing it here because you pull the rope to disconnect the trolley, run the trolley under power to the fully-open position, and then disconnect power before working on the door. Then you should lock the door down with either the security lock or with Vise-Grips or C-clamps. This avoids the door lifting when you don't expect it as you are applying spring adjustments. It you were to foolishly overwind the spring without the door locked down, you could possibly find the door trying to leap up to the raised position when you aren't prepared. That would likely knock your grip off the winding rods, with potentially disastrous results. I like to work under the safety principle that serious accidents should be physically possible only when you make two or more stupid mistakes at the same time.
With garage door installation costs, these numbers also include the actual purchase of the new door and other hardware, including the tracks, adhesives, connectors and fasteners. Keep in mind that if these numbers seem extreme, garage door replacement and upgrades can yield, on average, one of the highest returns on investments for homeowners — with an expected 85 percent.
Here is what a winding cone looks like without the spring. The threads that grip the inside of the spring coils are ambidextrous, so you can use the same part on either right- or left-hand-wound springs. The cone size is specific for a certain inner diameter of springs, so if you have the wrong size, the cone will slip inside the spring (cone too small), or not fit (cone too big).
Depending on the design, you can know in advance how many turns are going to have to be unwound. Lifting a 7-foot door by winding a cable on a 4-inch diameter (about 1 foot circumference) drum requires about 7 turns, plus one extra turn to maintain cable tension at the top-of-travel. Maintaining tension at the top-of-travel is critical; without it the cable will jump off the drum, requiring a serious repair.
The "liability" angle: The flip side of "safety issue" is "liability". This is not used to directly sell you something; it is used to demean the cheaper alternative and prod you into buying a more expensive (and profitable) option. For example, you may be pressured into buying a whole new door, when you just need a new spring, by the salesman telling you he can't just replace the spring due to "liability" issues. Since product liability is a big burden on the garage door industry, and so many old doors (and especially automatic openers) are dangerous, this may be a genuine reason to accept a higher price.
Most electric garage door openers have two lights: one in front of the opener and one behind or sometimes they sit side by side. They should provide enough light for you to get into your home from your car. Generally, people don’t leave the garage light on when it’s not in use, so it’s nice to have a temporary light when you arrive home. The length of time the light stays on varies according to how it is programmed. In most instances, you don’t need more than a few minutes from the time you leave the car to when you enter your home.
An entry may be the central tremendous moving piece of your home. It obliges routine upkeep practices to verify that it serves you for long, and chances of incidents are diminished. You will unquestionably take note that there are things you can do without anyone else to guarantee that it stays fit as a fiddle. However, when there is an issue, it is always recommended to call Local Garage Door Repair, Inc . When you select to do it independent from anyone else, without the obliged experience, you may end up exacerbating the issue or doing harm yourself and people around you.
Smart garage door openers aren't as expensive or hard to find as you might think. In fact, no matter what smart home platform you're using, there is an opener that will work for you. Smart garage door controllers add convenience like remote access, voice control, scheduling and vehicle detection to your garage door. You'll never need to wonder if you left it open ever again.
Overhead Door™ products automatically include the unequaled expertise of Overhead Door™ Distributors. Combined with our innovative product design and manufacturing superiority, our distributors are a proud part of the family, sharing our name, Red Ribbon logo, and commitment to excellence. Our network of more than 400 Overhead Door™ Distributors ensures you have convenient access to our commercial doors and operators, residential garage doors and openers, and accessories wherever you are. This extensive distribution network is unique in our industry, providing a single source for personalized design and application consulting, quick installation, turnkey services and professional maintenance.
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
We specialize in garage door Spring Replacements. Broken Garage Door Springs (Extension and Torsion) can be repaired on the spot. J&S Overhead Garage Door Service will replace your broken garage springs today. We use only the highest quality garage door parts available. Our Extension Springs and Torsion springs are designed to last longer than standard residential springs.
In each of our branches, we have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
Garage remotes work by sending a coded signal via radio frequency to the garage door opener. If this code matches that of the opener, then the motor will operate and raise or lower the door. Older devices use a single coded switch, whereas newer systems utilise a rolling code that changes each time the remote is used, increasing the security of the door by offering billions of combinations.
No matter what time or day of the week you require our services, we are always here to help. There are no additional fees to have us come by during the evening or weekend, so we’ll be able to offer you our premium service on a schedule that meets your needs. Contact Precision Garage Door Service of Lincoln today to book a free estimate and experience the high quality service that we have been providing to residents of Lincoln for many years.
The parts, parts, parts trick: You might be told you need new rollers, cables, drums, bearings, etc., when you don't, or at highly inflated prices. Good questions to ask when first calling for service include, "How do I know you will only charge me for the parts I actually need?", and "If you don't have all the parts I need, what will you charge me to come back?"
If you live in a home where there are living quarters directly above the garage, Garage Guide DIY says force-sensing technology built into the B730 ensures a smooth operation, no matter what temperature it is in your garage. The unit adjusts the motor's power on the fly, keeping it running smoothly. Amazon reviewer Steven Bone says the B730/WD962KEV opener runs extremely quietly and is easy to install.
Another recent innovation in the garage door opener is a fingerprint-based wireless keypad. This unit attaches to the outside of the garage door on the jamb and allows users to open and close their doors with the press of a finger, rather than creating a personal identification number (PIN). This is especially helpful for families with children who may forget a code and are latchkey kids.
Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
Horsepower is another key factor when it comes to garage door openers. Look into ½ horsepower garage openers if you have standard aluminum doors. Oversized doors and one-piece doors may require 3/4, 1 or 1¼ horsepower garage door openers. Garage openers with higher horsepower use less effort to operate and minimize wear and tear on the motor. This is ideal if your garage doors act as the main entrance to your home.
When garage door repair isn’t an option — perhaps the current door is beyond fixing or you want to upgrade to a quieter, more energy-efficient model — it’s time to buy a new one. But choosing a garage door is not as simple as it sounds, even when you know the right size for your home. A wide range of materials, styles and finishes are available, and each factor influences the cost. Garage doors are made of aluminum, steel, vinyl, fiberglass, masonite, wood (typically cedar or mahogany), or a composite of several materials. They may be insulated against cold or heat. Traditional and modern styles include raised panel, carriage house or crossbuck. Most styles have window or arch options, and are available in different wood finishes and neutral colors. Because garage doors account for a large part of a home’s exterior, their appearance is usually a homeowner’s top priority. An attractive garage door can increase a home’s curb appeal and resale value.
Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
There are such a large number of varied issues with carport entryway repair. Stray pieces will be the dependable wind up being free with time. A bothering sound when you work the entryway opener is a marker that there is an isolated wandering part. Prior to an opening, it ensures that that the power supply is standing alone from the framework, or else you may hurt yourself. Now and again the gaps for stray pieces can expand the extent of to a degree that you can’t fix them. In such a case, you can employ wood fillers or perhaps regular wood pieces to top them off.