The classic telephone bait-and-switch: This time-honored swindle, also called "false advertising", can show up in the garage door business. Here's how this scam works: When you call and say you have a broken spring, and ask for a repair price, you are told over the phone that the price is X dollars, which typically might seem a little better than the competition. When the repairman shows up, after looking at your broken door, he will casually and matter-of-factly tell you it will cost 2X. If they told you over the phone that it would cost X, well, that was only for one spring, and he must (he must, mind you) install not just one, but two. He will act surprised if you object, as if you should have known that from what you were told over the phone. If you expected to really pay just X, it was your fault for misunderstanding because you don't know anything about how garage doors should be repaired. (You will feel intimidated at this, since you honestly don't know anything, else why would you have called a repairman? Intimidation is a powerful tool against customer resistance.) If your door used only one spring to start with, he will insist on converting yours to two, telling you it is safer the next time a spring breaks. If you originally had two springs, he will tell you that he must replace both springs, and you must therefore pay double what was quoted. While it is true that converting or replacing both springs is a good idea, the bait-and-switch pricing is not. The "bait" is the low price quoted to you over the phone, which they never intended to honor, and the "switch" is switching the price to something higher on a pretense. This method of selling is literally criminal (for example, see Florida Statutes 817.44, all states have similar laws), but a service business can usually avoid detection or prosecution because there are no printed advertisements or other tangible evidence, just one-on-one phone calls. If you find yourself in the middle of this trap, then the proper response is to dismiss the repairman without paying a nickel. Don't expect that you will be able to negotiate a fair price with someone who is using criminal business methods. Certainly don't expect that he will accept a lower price because you accuse him of false advertising. If you absolutely cannot wait for another service call, then you'll have to accept the fraud, in which case you should do so quietly. People that use these methods typically have ways to mentally justify their behavior to themselves as a reasonable business practice, and won't react well to your suggesting otherwise, even though they are in fact small-time criminals, not shrewd businessmen.
Wayne Dalton garage doors are some of the best in the industry. We offer a large selection of garage door designs in many colors and options that can drastically enhance your home’s curb appeal. Not only will a new garage door add beauty to your home, but replacing an old or outdated door with a new one can increase your home’s value. Did you know that year after year replacing the garage door is one of the top home improvement projects for return on investment? Purchasing a new garage door for your home is an excellent investment and we’ve made it even easier to find the perfect door with our Garage Door Design Center or Garage Door Selection Guide.
We would definitely recommend Precision to anyone that needs garage door services! We were able to get a service appointment right away! Tom arrived and was very professional and courteous. He took the time to go over what repairs were needed and provided an estimate. He was ready to do the repairs right then and there and within a few hours, we had our garage door up and running like new! Thanks to Tom and Precision for a positive experience!

"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "


Insist on having any old parts returned to you, and have that noted on the written order before work begins. An honest and competent technician will not object to this. The evidence will establish whether you really needed the parts or not, and you can consult another opinion if you have any doubts. This tends to deter the parts-upsell scam, and protects you even if you know nothing about what you're buying while under the pressure of making a costly decision. If the old parts mysteriously "disappear", then you have reason to be suspicious.

While many sites may encourage you to save on garage door replacement costs by installing the door yourself, this is severely discouraged due to safety concerns and the installation techniques and tools required to properly and efficiently replace a garage door. When installing a new garage door, the range of prices also includes the labor performed by the professional garage door technician. These costs can include:
As your Kentucky and Ohio garage door repair company, we offer a team of experienced and knowledgeable technicians who move with urgency to diagnose your issues of any garage door repair or service They’ll discuss your options, and then execute the option you’ve selected for your home. When you need the best in garage door service, installation and repair, choose AE Door & Window.
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
We’ve been reviewing the best garage door openers for more than half a decade. This year we chose the Chamberlain Premium as our top pick. It’s an efficient, reliable garage door opener, and it comes with a backup battery system that works in a power outage. This model also has a preinstalled timer that closes your garage door automatically so you don't have to worry about whether you left the garage door open.

Clopay Garage Doors featuring Intellicore insulation technology represent Clopay Garage Doors featuring Intellicore insulation technology represent the ultimate smart choice for homeowners. Clopay Intellicore is proprietary polyurethane foam that is injected into a garage door expanding to fill the entire structure. The result is a door with incredible strength and durability. Its dense insulation also produces a quieter ...  More + Product Details Close
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
The best garage door openers can be controlled from a remote location through your phone. If you’ve ever left home and had a moment of panic, not knowing if you left the garage door open, this feature can give you peace of mind. The door opener’s built-in Wi-Fi connects directly with your home Wi-Fi router, which allows you to close your garage door from wherever you are through a MyQ smartphone app. The Chamberlain Group opener has this feature – it’s a 1-horsepower garage door opener with extra lifting power for unusually heavy doors of over 500 pounds.
Additionally, the B970 includes encryption features that prevent others from hacking the system to gain entry to your garage. Expert reviewers like this garage door opener a lot. The Tool Spy says the Chamberlain B970 justifies its higher price point by delivering excellent build quality and anti-vibration features. Consumer Search and Garage How To also approve of this unit.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!
Uncentered center bearing plate: The center bearing plate need not actually be in the center. It doesn't much matter where it is, since the purpose of the bracket is to anchor the spring ends. This anchoring must be secure, since all the torsion is held together at that point. On a stud-framed wall, this bracket may be placed over the stud closest to the center rather than exactly at the center of the door opening.
Mechanical garage door openers can pull or push a garage door with enough force to injure or kill people and pets if they become trapped. All modern openers are equipped with “force settings” that make the door reverse if it encounters too much resistance while closing or opening. Any garage door opener sold in the United States after 1992 requires safety eyes—sensors that prevent the door from closing if obstructed. Force settings should cause a door to stop or reverse on encountering more than approximately 20 lbs (9.07 kg) of resistance. Safety eyes should be installed a maximum of six inches above the ground. Many garage door injuries, and nearly all garage door related property damage, can be avoided by following these precautions.
Great!  We specialize in all sorts of garage door repair work.  Working around the garage door can be fairly dangerous if you’re trying to repair this issue on your own.  Most garage door companies will quickly remind folks about this, and it’s true.  Their are some hazards to watch out for when working around these heavy and high tension doors.  We recommend you give an expert a call to address the issue in a safe and timely manner for you.
Here’s an opener that comes with all the bells and whistles. Featuring an ultra quiet belt drive, you’ll be thankful you purchased one like this especially if you have a room positioned near or above the garage. It’s also got battery backup so if the power goes out, you can still get in and out with ease for up to 20 open and close cycles for the first 24 hours of an outage. And for the technology savvy will appreciate its MyQ smartphone control technology that allows you to control the door via an app on your iPhone or Android, plus you’ll receive safety notifications if you’re away from the house and the door opens or closes. And for extra peace of mind, there’s also a feature that will automatically close the door after a set amount of time — you know, just in case you forget.
An entry may be the central tremendous moving piece of your home. It obliges routine upkeep practices to verify that it serves you for long, and chances of incidents are diminished. You will unquestionably take note that there are things you can do without anyone else to guarantee that it stays fit as a fiddle. However, when there is an issue, it is always recommended to call Local Garage Door Repair, Inc . When you select to do it independent from anyone else, without the obliged experience, you may end up exacerbating the issue or doing harm yourself and people around you.

The open-ended work-order trick: You may be very surprised if you allow work to proceed without signing a work order with a specified price. Or, you may sign a work order, and think you're protected against open-ended wallet-reaching, only to find a much higher price due at the finish than you expected, because you signed a "parts as needed" order that got loaded up with a long list of parts (that likely were still in serviceable condition). You might have been quoted a price, but then get a bill for that price plus a lot more added for the "service call" and the "parts", and be told the quote was just for the labor. While this is the normal way of abusing your finances down at the hospital, you shouldn't agree to it for a garage door service call. These guys are not doctors.

When ordering springs, be aware that a number of different sizes of springs will make proper replacements, not just the specific size being replaced. The wire size, winding diameter, and length can be traded off to make springs of varied geometry but equivalent torque characteristics. This will also affect the expected lifetime (in cycles) for the spring(s). Since the critical specification for a replacement is the weight it is designed to bear, not the sizes per se, there are likely several stock sizes that replace a given old spring. The spring distributor's inventory may happen to offer only a different size with an equivalent weight-bearing specification. One has to judge whether to trust the advice of the seller in such situations. The seller should have the data to know what substitutions are proper.
Here's a view of my door and its broken torsion spring. This door is 10 feet wide and 7 feet high, constructed of 3/4 thick hollow wood panels inside with 3/4 inch plywood siding outside to match the house exterior. This is original to the house which was constructed in 1978, and is much heavier (238 pounds, as I measured later as described below) than the steel doors most common today in new construction. The 10-foot width is a little larger than usual for a one-car garage; such doors are typically only 7 or 9 feet wide. The ceiling height is 9 feet, providing 18 inches clearance above the torsion shaft. This is in a 3-car garage with 3 separate extra-wide doors. Every man's dream! ('cept when the door is broke.)

However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
While there might not be a huge price range when it comes to garage door openers—they are all quite an investment—there a few less expensive options to consider. Here’s a great budget option from Chamberlain. It has a motor that’s equivalent to ½ horsepower and chain drive system that is quick and easy to install. You can also connect it to the MQ technology (gateway sold separately) to use with your smartphone. The product comes with two three-button visor remote controls, a multi-function wall control, as well as a wireless keyless entry system. It comes with a 10-year motor, two-year parts, and one-year accessories warranty.

End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Overhead Door Company of Atlanta is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.
We would definitely recommend Precision to anyone that needs garage door services! We were able to get a service appointment right away! Tom arrived and was very professional and courteous. He took the time to go over what repairs were needed and provided an estimate. He was ready to do the repairs right then and there and within a few hours, we had our garage door up and running like new! Thanks to Tom and Precision for a positive experience!
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Since we're using an 18-inch (1.5 feet) winding lever to wind each spring up to 29 foot-pounds, we must apply a maximum tangential force to the end of the winding lever of about 20 pounds. Later we'll see that the actual weight of this rather dense door is 238 pounds, implying a maximum tangential force on the winding levers of only about 13 pounds!
I was careful not to assume that the previous installation correctly oriented the right- and left-hand springs on the correct sides of the center bearing plate. They could have been installed backwards by an incompetent installer, resulting in them having been wound looser (larger diameter coil) instead of tighter (smaller diameter coil) than when in their relaxed state, and if so I would have corrected them on the new installation. The proper orientation of the springs applies their reaction torque from tighter winding such that it turns the drums to lift the door. Verifying this is a rather simple exercise in mechanical visualization, but does require some care to be certain of correctness. If you were to install the springs backwards, and then start to wind them in the wrong direction, then the torsion bar will start winding the drums backwards, and not holding against the vise pliers, which should be obvious to inspection. Winding a spring backwards also tends to screw the spring off the cones; this error cannot proceed too far before the spring slips off the cones.
Manufacturers and distributors of torsion springs believe they are better off not retailing their product directly to the public. They believe they are maintaining higher prices for their product by restricting sales "to the trade." One brochure for parts even flatly stated, "We do not sell to the end user. We protect our dealers," which would seem to be prima facie evidence of an illegal restraint-of-trade scheme. But this is an old story which is true of virtually every product and service, going back to medieval guilds and before.
With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
While winding or unwinding, one must be mindful of the possibility that the spring could break during winding process itself. If that should happen while the spring is significantly torqued, hazardous forces on the winding bar will suddenly become unbalanced, and the bar will take an unexpected jump, possibly injuring your hand or anything else in its path. At the same time, the spring remnants, although captured on the torsion bar, will create a frightening racket that would give the bravest soul a start. So your winding technique should be firmly in control of the rods, and you should not be so delicately perched on a ladder such that a startle will result in a fall.
Checking if the lift drums need resetting: The old position of the lift drums on the shaft may have slipped or otherwise lost the the proper position, requiring a reset of the drum position on the torsion shaft. You will also reset the drums if you are replacing the lift cables, since the new cables will not exactly match the length of the old ones. Problems like uneven tension on the cables, or a tilted door, or a door that doesn't easily stay aligned with the tracks, can be due to an improper "set" of the drums on the shaft. So one shouldn't assume the old positions are correct. Setting the drums on a "fresh" part of the shaft will avoid the possibility of damaging the shaft from retightening in the same dimples.
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.

While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.


End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.

Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
A knowledgeable installer with good inventory can offer you upgraded spring lifetimes by using longer, heavier springs than were originally installed. For example, you may be offered more expensive springs with expected lifetimes of 15, 25, or even 100 thousand cycles, instead of the standard 10 thousand. The difference in labor to substitute this upgrade is nil. Since the dealer's cost of springs is proportional to weight, and typically a small part of the job price anyway, the dealer's cost for this upgrade is slight. This would seem to be a excellent option to offer every customer, and if correctly calculated and reasonably priced, one that you should take as cost-effective. Yet you may not be offered such an upgrade, if the installer is not adept at making the rather simple calculations, or if the optional springs are not on his truck, or if you're not around to be asked, or if the installer just doesn't like selling or taking time to discuss such details.
Another moment of truth arrives as the winding-up of the springs begins. (I am just posing here with the camera held out in my left hand. Except for lifting the door onto the scale, this was a one-man job, including the photography.) The position of the bars in this photo was necessary to take the photo, and does not show a correct winding technique, You should not have to swing the bar up as high over the top as shown. The lower bar during winding should swing from pointing down to pointing a little past horizontal. Then you hold that bar horizontal while socketing the other bar pointing down, apply force to that (now) lower bar, then remove the (now) upper bar, wind one-quarter turn, and repeat.
Since 2015, we’ve tested a variety of devices such as smart locks, video doorbells, DIY home security systems, thermostats and more. We use these testing experiences to inform our evaluations of other equipment. As time and resources allow, we occasionally test new types of products, but there are still some circumstances where we’re unable to conduct in-house tests. When testing isn’t possible, we conduct thorough research using the same standards we apply to our in-house tests – this is the case with smart garage door openers. We’ve reviewed garage door openers since 2011. 
As in an elevator, the electric motor does not provide most of the power to move a heavy garage door. Instead, most of door's weight is offset by the counterbalance springs attached to the door. (Even manually operated garage doors have counterbalances; otherwise they would be too heavy for a person to open or close them.) In a typical design, torsion springs apply torque to a shaft, and that shaft applies a force to the garage door via steel counterbalance cables. The electric opener provides only a small amount of force to control how far the door opens and closes. In most cases, the garage door opener also holds the door closed in place of a lock.
A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
×