The lucky-for-you-I-found-another-problem trick: Another trick is to suggest your automatic opener was damaged (or "compromised") by the additional load or shock presented by the failure of the spring(s). The plastic worm gear used in the most common openers (see above) wears normally over the years and tends to leave a lot of debris inside the opener housing. Removing the opener cover reveals a lot of plastic shavings that may be cited as "evidence" you need a new opener, when the gears are actually still serviceable. Nevertheless, you may have indeed worn out the gear if you repeatedly cycled the door with the opener despite having broken springs, which is possible if you have a very lightweight door.
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.

Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system including Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion setups on the spot.
We would definitely recommend Precision to anyone that needs garage door services! We were able to get a service appointment right away! Tom arrived and was very professional and courteous. He took the time to go over what repairs were needed and provided an estimate. He was ready to do the repairs right then and there and within a few hours, we had our garage door up and running like new! Thanks to Tom and Precision for a positive experience!
Bringing simple convenience to your home the Chamberlain Bringing simple convenience to your home the Chamberlain 1-1/4 HP Garage Door Opener provides instant garage access at your fingertips. Featuring innovative built-in smartphone control and battery backup this system ensures that you're never locked out of your home. Boasting a steel reinforced belt drive the B970 features anti-vibration technology ...  More + Product Details Close
Typically, it will cost less to install a steel garage door without an opener than to install a custom wood door with a garage door opener. Recent innovations have also yielded high-tech doors with thick insulation and energy-efficient glaze, as well as finished interior surfaces and other significant upgrades. These are more expensive doors, but they are also extremely durable.
It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, those also happen to be the kinds of days when cold and moisture combine to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is a minor icy connection between the two that can be broken when you hit the opener button.
Door repair business advice (warning to consumers, you are not allowed to know this): Thinner wire is excellent for shortening spring lifetimes, lightening your inventory on a service truck, and getting paid for frequent service calls. This is why your industry chooses to set "standard" springs to have thin wire and despicably short lifetimes. If you want to maximize profits and fleece your customers, install springs that predictably break in about 7 years on a door that should last decades, even though it is just as easy for you to install slightly more expensive springs that should last the life of the door. Remember that the customer wanted the cheapest price, so you need not feel any guilt about this low-balling.
End treatments: Torsion springs also are made in a variety of end treatments. The "standard torsion end" is most common, as is pictured in my examples, consisting simply of a short, straight length of wire projecting tangentially. Various non-standard end treatments have longer "ears", U-turns, ends bent in toward the center or along the axis, or even loops. Non-standard ends are used in end fasteners peculiar to various manufacturers, which would seem to serve mostly as a guarantee that you buy overpriced replacements from that one source.
Loosening or tightening the set-screws is the moment of most risk, since the end-wrench is a potential missile if you slip, and your hand is close to the cone. When the wrench is removed and only the rods are in place, it would seem that the worst that could happen is that the rod is flung out and the captive spring and cone rattle around, assuming you are keeping yourself clear of the rod's radial disk of rotation, and not leaning on the rod such as to fall into the apparatus were the rod to slip out of your grasp. The torsion shaft design has the virtue of capturing the mass of the spring and cones reliably on the shaft, preventing these parts from launching themselves as projectiles, even in an accident.
The not-so-competitive advertising trick: How about this racket: We have all heard how you should get at least three bids for any home improvement jobs, right? In some areas the largest ads in the yellow pages are from a single business using various names and phone numbers, masquerading as independent competitors. When you call asking for prices, "they" all quote you very high numbers. You are tricked into thinking you have shopped around for the prevailing price. (The more modern version of this is multiple Web sites that all direct you to call the same person.) If you've ever had to call a plumber you may have unknowingly been a victim of a similar trick.
When you’re thinking about replacing your garage door, there are many options to consider. Picking out materials and styles is sometimes stressful for homeowners. Neighborhood Garage Door Repair has some helpful tips on choosing the right material for your door. Garage Door Materials Manufacturers offer different materials when it comes to designing a garage door. […]
The garage door is the gateway to your home. By choosing an Overhead Door™ residential garage door, you are doing more than making a home improvement investment. You are making us a part of your daily life and relying on us for safety, security and dependable operation. Indulge your sense of design with a garage door that sets your home apart with style, appearance, safety and comfort. With dozens of garage door models to choose from, the Overhead Door™ brand provides style and design options to fit every home. ​
Two of the spring references specifically for the garage-door industry are the APCO Spring Manual by Bill Eichenberger, and the Torsion Spring Rate Book by Clarence Veigel; these give tables of spring sizes and torque constants. Spring engineering principles in general are described in the Handbook of Spring Design published by the Spring Manufacturer's Institute; the formulas allow you to calculate torque constants knowing only the geometry and the Young's modulus of the material. You can also find some brief spring information in standard references like Machinery's Handbook and Marks' Standard Handbook for Mechanical Engineers.
My door opener disengaged from the garage door. I made a call in late morning and was given an appointment for late the same afternoon. I received a call in early afternoon asking if I would like an earlier service call. Upon arriving the repair man introduced himself and explained that he would need a few minutes to assess the problem and perform an inspection. When he finished he provided me with a through explanation of the problem, the corrective measures he would take and some suggestions to improve operation. We discussed some options, agreed on the cost and the work was complete within a reasonable time frame. The door operates quieter and with less strain than it ever has. Pleasant, friendly, on-time and reasonably priced. Problem solved. It doesn't get any better than that.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
I've provided this information for free, in hopes it will help you either fix your door yourself, or find a competent professional service to do it for you at a reasonable price. If you've been helped by this Web page, as many have, all I would ask is that you create a link to this page (http://www.truetex.com/garage.htm) from any pages you maintain. You will thereby help others searching for complete and reliable information on this type of repair to find it with a Web search.
Establish an alternate entry to your garage or update an existing one with our selection of garage entry doors. With an entry door, you will lose less heat or air when you enter your garage to work. Our variety of garage and outdoor organization materials will help you keep all the items in your garage neatly and efficiently organized while our floor coatings and utility flooring will help ensure your cement garage floors last longer than if they were left untreated.
We also Specialize in frayed and broken garage door cables. Our expert technicians arrive equipped with fully stocked trucks, ready to repair or replace any garage door and opener system. Systems serviced include Liftmaster, Chamberlin, Sears, Craftsman, Genie, Clopay, Wayne Dalton, Amarr, Reliabilt, Raynor,C.H.I, and more. If the door system is unable to be repaired including Wayne Dalton torqmaster setups and needs to be replaced, our technicians are able to upgrade the garage door system with extension or torsion garage door spring systems on the spot.
Kevin gave 30 mins advance notice via text before arriving, and he was very friendly and knowledgeable about the Chamberlain garage door opener that we ordered on Amazon. I was pleased with the thorough model description provided, and customer reviews which helped with our decision making, and our package came on the same day that it was ordered! I liked the process of choosing 3 preferred appointment times, and receiving a confirmation email which included Kevin's picture. The install price was very reasonable, and I would gladly use your Home Service again!
Spring rate, torque, and lift: The spring rate K for these measurements is π*28.5*10^6 * (0.273)^4 / (32 * 140 * 1.72) = 64.5 IPPT. Applying 7.5 turns on this rate will yield a torque of 7.5 * 64.5 = 484 in-lb, which on the 4-inch drums (2-inch radius) yields a lift of (484 in*lbs)/(2 in) = 242 lbs. Again we find good agreement with the approximate door weight of 238 lbs.

Before setting the last panel in the tracks, set the power unit on the actual frame and slide it in the ends. Hardened screws are used to attach the center bracket (Image 1). They are a different type screw — they are tougher and will last a lot longer. Make sure the bracket is level (to the eye) when installed and leave the bracket a little loose so adjustments can be made. Fasten down all the hinges (Image 2).
Note that I am measuring a spring that is fully relaxed because it is broken!. The length of the relaxed, unbroken spring is the specification of interest. It is harder to measure unbroken springs on an intact door because the springs should not fully unwind, even at the top-of-travel. If you can't be certain of the spring diameter from indications on the cones, then you have to go through an unwinding procedure to relax them fully for measurement, or perhaps reckon the size from measuring the somewhat smaller diameter at the nearly unwound condition when the door is at its top-of-travel (although one should not attempt to raise a door with a broken spring).
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects.
For more than 35 years, AE Door & Window has served the Cincinnati and Northern Kentucky areas with high-quality Clopay garage door products and exceptional services. We started as a small company operating out of a garage. In the decades since we first opened, we’ve grown into a regional provider that businesses and homeowners turn to when they need garage door products, services and repairs.
Although the door weight and drum size determine the maximum torque (termed MIP, maximum inch-pounds) needed from the fully-wound spring(s), the spring selection for a given door can still be varied to adjust the cycling stresses. A heavier wire on a larger diameter or longer length will produce the same torque as a lighter wire on a smaller diameter or shorter length, while undergoing less stress and therefore increasing expected cycle lifetime. The heavier spring will cost more but last longer, so this is another design trade-off. Calculating these spring sizes in the field is done using a book of tables (or the software equivalent) that we cannot provide here, although you will find the formulas to estimate spring properties below. If you can accurately provide the weight of the door, or the size(s) of the old spring(s) (assuming they were well-matched to balance the door), then a spring dealer should be able to tell you which spring sizes will work for you.
Garage Doors have a great variety of features and also come in a wide range of prices. If you're considering the purchase a new garage door, please allow our experienced garage door technicians to come to your home to acquaint you with all the possibilities. Buying a garage door is not just about purchasing the door, but also selecting the company that will install it. We offer perhaps the lowest price in new garage doors because our experience has taught us to be efficient in what we do. Just call us. We'll be on the way to your home or business quickly.

"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."

You might genuinely need some extra parts when you thought you simply needed a broken spring replaced, and a good serviceman will perform a simple inspection to identify such parts. Nor is it unreasonable for a business to charge separately for a service call versus repair work actually performed. But the best protection for you as a buyer, being somewhat at the mercy of whomever you decide to bring on site, is to understand what is being done, and ask intelligently for a clear explanation or demonstration of why extra parts are required.


Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]


Repair of garage doors is a licensed trade in many jurisdictions, and manipulation of the market inevitably follows. Look in your phone book yellow-pages under "garage doors" and you'll find a lot of big, costly ads for door service. The profits are quite juicy, I'm sure. The customers need service urgently, and this need will typically arrive suddenly and at a busy time when shopping for prices is not convenient. A few dollars in parts, an hour of labor and travel, and a $150 invoice (assuming the outfit is charging fairly, some are not). Lately (2006) I hear of outfits charging $200 or $300 for this work, and occasionally a story of a $500 or $800 service call. You'll also find the phonebook advertisers waiting eagerly for your call, because artificially high prices inevitably lead to an oversupply of service firms working under capacity.

Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost, give us a call at 480-641-2301 or use our Contact Page.
The electric overhead garage door opener was invented by C.G. Johnson in 1926 in Hartford City, Indiana.[1] Electric Garage Door openers did not become popular until Era Meter Company of Chicago offered one after World War II where the overhead garage door could be opened via a key pad located on a post at the end of the driveway or a switch inside the garage.[2]
While a new coat of paint can go a long way in improving the look of your garage door, the truth is that door design has come a long way in the years since garages were first installed in homes. Not only are newer doors more in line with current fashion trends, but they are also better sized for today’s cars. A new, contemporary door is a great way to get an immediate boost on the value of your home.
Roberto was very courteous and explained the details of what he was doing. He also pointed out a repair I might consider having done (replacement of the bottom panel of my door) and asked the office to follow up with me on this. Someone did follow up with me and since replacement of the bottom panel is not an option and I would have to replace the door, I decided that I can wait.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.
This opener is easy to install for most DIYers and comes with two remotes and a wireless keypad so you can open the door with a pin. If you are interested in having this smart-enabled you can purchase a separate kit to do so. The Safe-T Beam helps prevent accidents using a infrared beam that will open or close the door if a car is getting to close. 

Most garage door openers are pretty expensive. So if you need an opener on a budget, the Genie 1035-V (also known as the Genie Chain Drive 500) gives you that desirable low price point. It doesn't have a lot of high-end tech features, nor will it manage heavy garage doors, but it does the basic work of raising and lowering the garage door perfectly well.
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
Clopay, a garage door manufacturer, provides online installation manuals for their products. These include excellent mechanical diagrams and brief instructions for winding torsion springs on their doors. Of course, this is specific to their product designs, which may or may not match what you have. Note that some of their products involve the "EZ-Set assembly option" mechanisms that use a geared housing for winding (instead of standard winding cones) and non-standard geometry for the drums. Clopay should get an award for at least acknowledging in their instructions that you might be able to install your own new door (although they insist you must not take out an old one if it has torsion springs).
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
The classic telephone bait-and-switch: This time-honored swindle, also called "false advertising", can show up in the garage door business. Here's how this scam works: When you call and say you have a broken spring, and ask for a repair price, you are told over the phone that the price is X dollars, which typically might seem a little better than the competition. When the repairman shows up, after looking at your broken door, he will casually and matter-of-factly tell you it will cost 2X. If they told you over the phone that it would cost X, well, that was only for one spring, and he must (he must, mind you) install not just one, but two. He will act surprised if you object, as if you should have known that from what you were told over the phone. If you expected to really pay just X, it was your fault for misunderstanding because you don't know anything about how garage doors should be repaired. (You will feel intimidated at this, since you honestly don't know anything, else why would you have called a repairman? Intimidation is a powerful tool against customer resistance.) If your door used only one spring to start with, he will insist on converting yours to two, telling you it is safer the next time a spring breaks. If you originally had two springs, he will tell you that he must replace both springs, and you must therefore pay double what was quoted. While it is true that converting or replacing both springs is a good idea, the bait-and-switch pricing is not. The "bait" is the low price quoted to you over the phone, which they never intended to honor, and the "switch" is switching the price to something higher on a pretense. This method of selling is literally criminal (for example, see Florida Statutes 817.44, all states have similar laws), but a service business can usually avoid detection or prosecution because there are no printed advertisements or other tangible evidence, just one-on-one phone calls. If you find yourself in the middle of this trap, then the proper response is to dismiss the repairman without paying a nickel. Don't expect that you will be able to negotiate a fair price with someone who is using criminal business methods. Certainly don't expect that he will accept a lower price because you accuse him of false advertising. If you absolutely cannot wait for another service call, then you'll have to accept the fraud, in which case you should do so quietly. People that use these methods typically have ways to mentally justify their behavior to themselves as a reasonable business practice, and won't react well to your suggesting otherwise, even though they are in fact small-time criminals, not shrewd businessmen.

Your garage door is used often, generally more than any other door on your home. Therefore, it’s important to make sure that it’s tough, dependable and weather resistant. Our doors are fully capable of meeting all these requirements and are specifically designed with our customers in mind. While durability is important, so is appearance and we offer many different styles and colors of garage doors to match your home or business.


Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]
×